参数资料
| 型号： | AD8390AACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LP LDIST 16LFCSP |
| 标准包装： | 1,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 300 V/µs |
| -3db带宽： | 60MHz |
| 电流 - 输入偏压： | 4µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 10mA |
| 电流 - 输出 / 通道： | 400mA |
| 电压 - 电源，单路/双路(±)： | 10 V ~ 24 V，±5 V ~ 12 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-VQ |
| 包装： | 带卷 (TR) |
AD8390A
Data Sheet
Rev. B | Page 10 of 12
APPLICATIONS INFORMATION
SUPPLIES, GROUNDING, AND LAYOUT
The AD8390A can be powered from either single or dual
supplies, with the total supply voltage ranging from 10 V to
24 V. For optimum performance, use well-regulated low ripple
supplies.
As with all high speed amplifiers, pay close attention to supply
decoupling, grounding, and overall board layout. Provide low
frequency supply decoupling with 10 F tantalum capacitors
from each supply to ground. In addition, decouple all supply
pins with 0.1 F quality ceramic chip capacitors placed as close
as possible to the driver. Use an internal low impedance ground
plane to provide a common ground point for all driver and
decoupling capacitor ground requirements. Whenever possible,
use separate ground planes for analog and digital circuitry.
Follow high speed layout techniques to minimize parasitic
capacitance around the inverting inputs. Some practical
examples of these techniques are keeping feedback traces as
short as possible and clearing away ground plane in the area of
the inverting inputs.
Keep input and output traces as short as possible and as far
apart from each other as practical to minimize crosstalk. Keep
all differential signal traces as symmetrical as possible.
VCOM PIN
By design, the VCOM pin is internally biased at midsupply,
eliminating the need for external resistors. However, the
designer may set VCOM to other voltage levels with an external
low impedance source.
When the VCOM pin is left unconnected, decouple it with a
0.1 F capacitor to ground, placed in close proximity to the
AD8390A.
With dual equal supplies, connect the VCOM pin directly to
ground to bias the outputs at midsupply, eliminating the need
for the external decoupling capacitor.
POWER MANAGEMENT
The AD8390A offers significant versatility for maximizing
efficiency while maintaining optimal levels of performance.
Optimizing driver efficiency while delivering the required signal
level is accomplished with two on-chip power management
features: two PD pins to select one of four bias modes and an
IADJ pin for fine bias adjustments.
PD(1:0) Pins
Two CMOS-compatible logic pins, PD1 and PD0, select one of
three active power levels and a power-down mode.
The digital ground pin (DGND) is the logic ground reference
for the PD(1:0) pins. PD(1:0) = (0,0) is the power-down mode.
The PD pins are internally connected to DGND via termination
resistors. When the PD pins are left unconnected, the AD8390A
is in power-down mode.
The AD8390A exhibits a low output impedance in the three
active modes. The output impedance in the power-down mode
is high but undefined and may not be suitable for systems that
rely on a high impedance OFF state, such as multiplexing.
IADJ Pin
The IADJ pin provides bias current fine-tuning.
With the IADJ pin unconnected, the bias currents are internally
set to 10 mA, 6.7 mA, and 3.8 mA for the three active modes.
With the IADJ pin connected to the negative supply (VEE), the
bias currents are reduced by approximately 50%.
A resistor, RADJ, connected between the IADJ pin and the negative
supply, provides fine bias adjustment as shown in Figure 8.
Table 5. PD and IADJ Selection Guide
PD1
PD0
RADJ ()
IQ (mA)
1
∞
10.0
1
0
∞
6.7
0
1
∞
3.8
0
∞
0.67
1
0
5.5
1
0
4.0
0
1
0
2.6
0
0.56
相关PDF资料 |
PDF描述 |
|---|---|
| AD8532ARZ | IC OPAMP GP R-R CMOS 3MHZ 8SOIC |
| FFB1248VHE-R00 | FAN 120MM X 38MM 48VDC |
| AD8571ARMZ-REEL | IC OPAMP CHOPPER R-R 30MA 8MSOP |
| AD8671ARMZ-REEL | IC OPAMP GP 10MHZ PREC LN 8MSOP |
| 929835-01-04 | CONN HEADER .100 SNGL R/A 4POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8390AACPZ-RL | 功能描述:IC AMP DIFF LP LDIST 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| AD8390ACP-EVAL | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, High Output Current Differential Amplifier |
| AD8390ACP-R2 | 功能描述:IC AMP DIFF LP LDIST 16LFCSP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| AD8390ACP-REEL | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single ±12V/24V 16-Pin LFCSP EP T/R |
| AD8390ACP-REEL7 | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 制造商:Rochester Electronics LLC 功能描述:ADSL LINE DRIVER - Tape and Reel 制造商:Analog Devices 功能描述:IC AMP LOW POWER |
发布紧急采购，3分钟左右您将得到回复。