- 您现在的位置：买卖IC网 > PDF目录10157 > AD8398ACPZ-RL (Analog Devices Inc)IC LINE DRIVER DUAL VDSL 16LFCSP PDF资料下载
参数资料
| 型号： | AD8398ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC LINE DRIVER DUAL VDSL 16LFCSP |
| 标准包装： | 5,000 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 2/0 |
| 规程： | xDSL |
| 电源电压： | 12V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-WQ（4x4） |
| 包装： | 带卷 (TR) |
AD8398A
Rev. D | Page 8 of 12
APPLICATIONS INFORMATION
POWER CONTROL MODES OF OPERATION
The AD8398A features four power modes: full power, medium
power, low power, and complete power-down. Two CMOS-
compatible logic pins (PD0 and PD1) select the power mode.
The power modes and associated logic states are listed in Table 5.
Table 5. Power Modes
PD1
PD0
Power Mode
Total Supply Current (mA)
0
Full power
33.2
0
1
Medium power
22.9
1
0
Low power
13.3
1
Power-down
0.7
EXPOSED THERMAL PAD CONNECTIONS
To ensure adequate heat transfer away from the die, connect
the exposed thermal pad to a solid plane layer with low thermal
resistance. To maximize the operating life of the AD8398A, the
thermal design of the system should be kept below the junction
temperature of 125°C.
Although it is electrically isolated, the thermal pad typically
connects to the ground plane layer.
POWER SUPPLY BYPASSING
The AD8398A typically operates on ±6 V or +12 V supplies.
Power the AD8398A circuit with a well-regulated, properly
decoupled power supply. To minimize supply voltage ripple
and power dissipation, use high quality capacitors with low
equivalent series resistance (ESR), such as multilayer ceramic
capacitors (MLCCs). Place a decoupling 0.1 μF MLCC no
more than inch away from each of the power supply pins.
In addition, a 10 μF tantalum capacitor is recommended to
provide good decoupling for lower frequency signals and to
supply current for fast, large signal changes at the AD8398A
outputs. Lay out bypass capacitors to keep return currents away
from the inputs of the amplifiers. This layout minimizes any
voltage drops that can develop due to ground currents flowing
through the ground plane.
BOARD LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. Proper RF design
technique is mandatory.
The PCB has a ground plane covering all unused portions of the
component side of the board to provide a low impedance return
path. Removing the ground plane on all layers from the area
near the input and output pins of the AD8398A reduces stray
capacitance.
Signal lines connecting the feedback and gain resistors should
be as short as possible to minimize the inductance and stray
capacitance associated with these traces. Place termination resistors
and loads as close as possible to their respective inputs and outputs.
To minimize coupling (crosstalk) through the board, keep input
and output traces as far apart as possible. Wherever there are
complementary signals, provide a symmetrical layout to maximize
balanced performance.
相关PDF资料 |
PDF描述 |
|---|---|
| 1M7807-15PAGG4 | IC FIFO MEMORY 2048X9 64-TQFP |
| VE-22R-IW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
| LTC1605-2IG#TRPBF | IC A/D CONV 16BIT SAMPLNG 28SSOP |
| LTC1605-2IG#TR | IC ADC 16BIT 5V SAMPLING 28SSOP |
| SN74ACT7807-15PAG | IC SYNC FIFO MEM 2048X9 64-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8398ACPZ-TR | 制造商:Analog Devices 功能描述:DUAL WIDEBAND HI OUTPUT CURRENT OPAMP - Tape and Reel |
| AD83C151C-12 | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| AD83C151C-16 | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| AD83C151C-20 | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| AD83C151C-25 | 制造商:TEMIC 制造商全称:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。