- 您现在的位置：买卖IC网 > PDF目录373947 > AD8531AR (ANALOG DEVICES INC) Low Cost, 250 mA Output Single-Supply Amplifiers PDF资料下载
参数资料
| 型号： | AD8531AR |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 运动控制电子 |
| 英文描述： | Low Cost, 250 mA Output Single-Supply Amplifiers |
| 中文描述： | OP-AMP, 30000 uV OFFSET-MAX, 2.2 MHz BAND WIDTH, PDSO8 |
| 封装： | MS-012AA, SOIC-8 |
| 文件页数： | 9/16页 |
| 文件大小： | 417K |
| 代理商： | AD8531AR |
AD8531/AD8532/AD8534
REV. D
–9–
Power Dissipation
Although the AD8531/AD8532/AD8534 is capable of providing
load currents to 250 mA, the usable output load current drive
capability will be limited to the maximum power dissipation
allowed by the device package used. In any application, the
absolute maximum junction temperature for the AD8531/
AD8532/AD8534 is 150
∞
C, and should never be exceeded for
the device could suffer premature failure. Accurately measuring
power dissipation of an integrated circuit is not always a
straightforward exercise, so Figure 34 has been provided as a
design aid for either setting a safe output current drive level or
in selecting a heatsink for the package options available on the
AD8531/AD8532/AD8534.
TEMPERATURE – C
1.5
1
00
100
25
50
75
0.5
85
T
J
MAX = 150 C
FREE AIR
NO HEATSINK
SOIC
JA
= 158 C/W
TS = 240 C/W
JA
SO = 236 C/W
JA
SC70
JA
= 376 C/W
P
Figure 34. Maximum Power Dissipation vs. Ambient
Temperature
These thermal resistance curves were determined using the
AD8531/AD8532/AD8534 thermal resistance data for each
package and a maximum junction temperature of 150
∞
C. The
following formula can be used to calculate the internal junction
temperature of the AD8531/AD8532/AD8534 for any application:
T
J
=
P
DISS
￥
q
J
A
+ T
A
where
T
J
= junction temperature;
P
DISS
= power dissipation;
q
J
A
= package thermal resistance,
junction-to-case; and
T
A
= Ambient temperature of the circuit.
To calculate the power dissipated by the AD8531/AD8532/
AD8534, the following equation can be used:
P
DISS
=
I
LOAD
￥
(
V
S
–V
OUT
)
where
I
LOAD
= is output load current;
V
S
= is supply voltage; and
V
OUT
= is output voltage.
The quantity within the parentheses is the maximum voltage
developed across either output transistor. As an additional
design aid in calculating available load current from the
AD8531/AD8532/AD8534, Figure 1 illustrates the AD8531/
AD8532/AD8534 output voltage as a function of load resistance.
Power Calculations for Varying or Unknown Loads
Often, calculating power dissipated by an integrated circuit to
determine if the device is being operated in a safe range is not
as simple as it might seem. In many cases power cannot be
directly measured. This may be the result of irregular output
waveforms or varying loads; indirect methods of measuring
power are required.
There are two methods to calculate power dissipated by an
integrated circuit. The first can be done by measuring the pack-
age temperature and the board temperature. The other is to
directly measure the circuit’s supply current.
Calculating Power by Measuring Ambient and Case
Temperature
Given the two equations for calculating junction temperature:
T
J
=
T
A
+
P
q
J
A
where
T
J
is junction temperature, and
T
A
is ambient tempera-
ture.
q
J
A
is the junction to ambient thermal resistance.
T
J
=
T
C
+ P
q
J
C
where
T
C
is case temperature and
q
J
A
and
q
J
C
are given in the
data sheet.
The two equations can be solved for
P
(power):
T
A
+
P
q
J
A
= T
C
+ P
q
J
C
P = (T
A
– T
C
)/ (
q
J
C
–
q
J
A
)
Once power has been determined it is necessary to go back and
calculate the junction temperature to assure that it has not been
exceeded.
The temperature measurements should be directly on the pack-
age and on a spot on the board that is near the package but
definitely not touching it. Measuring the package could be diffi-
cult. A very small bimetallic junction glued to the package could
be used or it could be done using an infrared sensing
device if the spot size is small enough.
Calculating Power by Measuring Supply Current
Power can be calculated directly knowing the supply voltage and
current. However, supply current may have a dc component
with a pulse into a capacitive load. This could make rms current
very difficult to calculate. It can be overcome by lifting the sup-
ply pin and inserting an rms current meter into the circuit. For
this to work you must be sure all of the current is being deliv-
ered by the supply pin you are measuring. This is usually a good
method in a single supply system; however, if the system uses
dual supplies, both supplies may need to be monitored.
Input Overvoltage Protection
As with any semiconductor device, whenever the condition
exists for the input to exceed either supply voltage, the device’s
input overvoltage characteristic must be considered. When an
overvoltage occurs, the amplifier could be damaged depending
on the magnitude of the applied voltage and the magnitude of
the fault current. Although not shown here, when the input
voltage exceeds either supply by more than 0.6 V, pn-junctions
internal to the AD8531/AD8532/AD8534 energize allowing
current to flow from the input to the supplies. As illustrated in
the simplified equivalent input circuit (Figure 32), the AD8531/
AD8532/AD8534 does not have any internal current limiting
resistors, so fault currents can quickly rise to damaging levels.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8531ART | Low Cost, 250 mA Output Single-Supply Amplifiers |
| AD8531 | Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA输出,单电源放大器) |
| AD8532 | Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA输出,单电源双放大器) |
| AD8534 | Low Cost, 250 mA Output Single-Supply Amplifiers(低成本,250mA输出,单电源四放大器) |
| AD8538_07 | Low Power, Precision, Auto-Zero Op Amps |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8531AR-REEL | 制造商:Analog Devices 功能描述:OP Amp Single GP R-R I/O 6V 8-Pin SOIC N T/R |
| AD8531ART | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, 250 mA Output Single-Supply Amplifiers |
| AD8531ART-REEL | 制造商:Analog Devices 功能描述:OP Amp Single GP R-R I/O 6V 5-Pin SOT-23 T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE 250MA RAIL TO RAIL OP AMP - Tape and Reel |
| AD8531ART-REEL7 | 制造商:Analog Devices 功能描述:OP Amp Single GP R-R I/O 6V 5-Pin SOT-23 T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE 250MA RAIL TO RAIL OP AMP - Tape and Reel |
| AD8531ARTZ-REEL | 功能描述:IC OPAMP GP R-R CMOS SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:160 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:10 V/µs 增益带宽积:9MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:250µV 电流 - 电源:730µA 电流 - 输出 / 通道:28mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。