参数资料
| 型号： | AD8531ARTZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R CMOS SOT23-5 |
| 标准包装： | 10,000 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 5 V/µs |
| 增益带宽积： | 3MHz |
| 电流 - 输入偏压： | 5pA |
| 电压 - 输入偏移： | 25000µV |
| 电流 - 电源： | 750µA |
| 电流 - 输出 / 通道： | 250mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 6 V，±1.35 V ~ 3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
AD8531/AD8532/AD8534
Rev. F | Page 14 of 20
APPLICATIONS INFORMATION
HIGH OUTPUT CURRENT, BUFFERED
REFERENCE/REGULATOR
Many applications require stable voltage outputs relatively close
in potential to an unregulated input source. This low dropout
type of reference/regulator is readily implemented with a rail-
to-rail output op amp and is particularly useful when using a
higher current device, such as the AD8531/AD8532/AD8534.
A typical example is the 3.3 V or 4.5 V reference voltage developed
from a 5 V system source. Generating these voltages requires a
three terminal reference, such as the REF196 (3.3 V) or the
REF194 (4.5 V), both of which feature low power, with sourcing
outputs of 30 mA or less. Figure 42 shows how such a reference
can be outfitted with an AD8531/AD8532/AD8534 buffer for
higher currents and/or voltage levels, plus sink and source load
capability.
R2
10k 1%
VOUT1 =
3.3V @ 100mA
R5
0.2
C5
100F/16V
TANTALUM
R1
10k
1%
C1
0.1F
VS
5V
VOUT2 =
3.3V
C4
1F
6
2
3
4
VOUT
COMMON
C3
0.1F
C2
0.1F
VC
ON/OFF
CONTROL
INPUT CMOS HI
(OR OPEN) = ON
LO = OFF
VS
COMMON
R3
(See Text)
R4
3.3k
U2
AD8531
U1
REF196
01
099
-042
Figure 42. High Output Current Reference/Regulator
The low dropout performance of this circuit is provided by
stage U2, an AD8531 connected as a follower/buffer for the
basic reference voltage produced by U1. The low voltage
saturation characteristic of the AD8531/AD8532/AD8534
allows up to 100 mA of load current in the illustrated use,
as a 5 V to 3.3 V converter with good dc accuracy. In fact,
the dc output voltage change for a 100 mA load current delta
measures less than 1 mV. This corresponds to an equivalent
output impedance of < 0.01 Ω. In this application, the stable
3.3 V from U1 is applied to U2 through a noise filter, R1 to C1.
U2 replicates the U1 voltage within a few millivolts, but at a
higher current output at VOUT1, with the ability to both sink and
source output current(s), unlike most IC references. R2 and C2
in the feedback path of U2 provide additional noise filtering.
Transient performance of the reference/regulator for a 100 mA
step change in load current is also quite good and is largely
determined by the R5 to C5 output network. With values as
shown, the transient is about 20 mV peak and settles to within
2 mV in less than 10 μs for either polarity. Although room exists
for optimizing the transient response, any changes to the R5 to
C5 network should be verified by experiment to preclude the
possibility of excessive ringing with some capacitor types.
To scale VOUT2 to another (higher) output level, the optional
resistor R3 (shown dotted in Figure 42) is added, causing the
new VOUT1 to become
+
×
=
R3
R2
V
OUT2
OUT1
1
The circuit can either be used as shown, as a 5 V to 3.3 V
reference/regulator, or with on/off control. By driving Pin 3 of
U1 with a logic control signal as noted, the output is switched
on/off. Note that when on/off control is used, R4 must be used
with U1 to speed on/off switching.
SINGLE-SUPPLY, BALANCED LINE DRIVER
The circuit in Figure 43 is a unique line driver circuit topology
used in professional audio applications. It was modified for
automotive and multimedia audio applications. On a single 5 V
supply, the line driver exhibits less than 0.7% distortion into a
600 Ω load from 20 Hz to 15 kHz (not shown) with an input
signal level of 4 V p-p. In fact, the output drive capability of the
AD8531/AD8532/AD8534 maintains this level for loads as
small as 32 Ω. For input signals less than 1 V p-p, the THD is
less than 0.1%, regardless of load. The design is a transformer-
less, balanced transmission system where output common-
mode rejection of noise is of paramount importance. As with
the transformer-based system, either output can be shorted
to ground for unbalanced line driver applications without changing
the circuit gain of 1. Other circuit gains can be set according to the
equation in the diagram. This allows the design to be easily
configured for inverting, noninverting, or differential operation.
RL
600
C1
22F
A2
7
6
5
3
1
2
A1
5V
R1
10k
R2
10k
R11
10k
R7
10k
6
7
5
A1
12V
5V
R8
100k
R9
100k
C2
1F
R12
10k
R14
50
A2
1
2
3
R3
10k
R6
10k
R13
10k
C3
47F
VOUT1
VOUT2
C4
47F
A1, A2 = 1/2 AD8532
GAIN = R3
R2
SET: R7, R10, R11 = R2
SET: R6, R12, R13 = R3
VIN
R10
10k
R5
50
01
099
-0
43
Figure 43. Single-Supply, Balanced Line Driver for Multimedia and
Automotive Applications
相关PDF资料 |
PDF描述 |
|---|---|
| 51760-10402002AA | R/A SOLDER REC.PWRBLADE |
| GTC35SGSN-M89 | CONN HEADER 35POS .100 R/A SMD |
| GTC34SGSN-M89 | CONN HEADER 34POS .100 R/A SMD |
| AD8541ARTZ-REEL | IC OPAMP GP R-R CMOS SOT23-5 |
| SMAJ110A-13 | TVS UNI-DIR 110V 400W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8531ARTZ-REEL7 | 功能描述:IC OPAMP GP R-R CMOS SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 特色产品:CMOS Operational Amplifier 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:1000µV 电流 - 电源:900µA 电流 - 输出 / 通道:1mA 电压 - 电源，单路/双路(±):5 V ~ 14.5 V，±2.5 V ~ 7.25 V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-SOP 包装:带卷 (TR) 产品目录页面:1372 (CN2011-ZH PDF) 其它名称:BD7562SF-E2TR |
| AD8531ARTZ-REEL7 | 制造商:Analog Devices 功能描述:IC OP-AMP 3MHZ 5V/S SOT-23-5 |
| AD8531ARZ | 功能描述:IC OPAMP GP R-R CMOS 3MHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| AD8531ARZ-REEL | 功能描述:IC OPAMP GP R-R CMOS 3MHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 特色产品:CMOS Operational Amplifier 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:1000µV 电流 - 电源:900µA 电流 - 输出 / 通道:1mA 电压 - 电源，单路/双路(±):5 V ~ 14.5 V，±2.5 V ~ 7.25 V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-SOP 包装:带卷 (TR) 产品目录页面:1372 (CN2011-ZH PDF) 其它名称:BD7562SF-E2TR |
| AD8532 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, 250 mA Output Single-Supply Amplifiers |
发布紧急采购，3分钟左右您将得到回复。