- 您现在的位置：买卖IC网 > PDF目录17027 > AD9233-125EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9233 PDF资料下载
参数资料
| 型号： | AD9233-125EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/44页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9233 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 125M |
| 数据接口： | 串行 |
| 输入范围： | 1 ~ 2 Vpp |
| 在以下条件下的电源（标准）： | 455mW @125MSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD9233 |
| 已供物品： | 板，电源 |
| 相关产品： | AD9233BCPZRL7-125-ND - IC ADC 12BIT 125MSPS 48-LFCSP AD9233BCPZRL7-105-ND - IC ADC 12BIT 105MSPS 48-LFCSP AD9233BCPZ-105-ND - IC ADC 12BIT 105MSPS 48-LFCSP AD9233BCPZ-125-ND - IC ADC 12BIT 80/105/125 48-LFCSP AD9233BCPZ-80-ND - IC ADC 12BIT 80MSPS 48-LFCSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AD9233
Rev. A | Page 23 of 44
SERIAL PORT INTERFACE (SPI)
The AD9233 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space provided inside the ADC. This provides the user added
flexibility and customization depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that
are further divided into fields, as documented in the Memory
Map section. For detailed operational information, see the
CONFIGURATION USING THE SPI
As summarized in Table 13, three pins define the SPI of this
ADC. The SCLK/DFS pin synchronizes the read and write data
presented to the ADC. The SDIO/DCS dual-purpose pin allows
data to be sent and read from the internal ADC memory map
registers. The CSB pin is an active low control that enables or
disables the read and write cycles.
Table 13. Serial Port Interface Pins
Mnemonic
Description
SCLK/DFS
SCLK (Serial Clock) is the serial shift clock in. SCLK
synchronizes serial interface reads and writes.
SDIO/DCS
SDIO (Serial Data Input/Output) is a dual-purpose
pin. The typical role for this pin is an input and
output depending on the instruction being sent
and the relative position in the timing frame.
CSB
CSB (Chip Select Bar) is an active low control that
gates the read and write cycles.
The falling edge of the CSB in conjunction with the rising edge
of the SCLK determines the start of the framing. Figure 57 and
Table 14 provide an example of the serial timing and its
definitions.
Other modes involving the CSB are available. The CSB can be
held low indefinitely, permanently enabling the device (this is
called streaming). The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high
during power up, SPI functions are placed in a high impedance
mode. This mode turns on any SPI pin secondary functions. If
CSB is high at power up and then brought low to activate the
SPI, the SPI pin secondary functions are no longer available,
unless the device power is cycled.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase and the length is determined
by the W0 bit and the W1 bit. All data is composed of 8-bit
words. The first bit of each individual byte of serial data indicates
whether a read or write command is issued. This allows the
serial data input/output (SDIO) pin to change direction from
an input to an output.
In addition to word length, the instruction phase determines if
the serial frame is a read or write operation, allowing the serial
port to be used to both program the chip as well as read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB first or in LSB first mode. MSB first is
the default on power up and can be changed via the
configuration register. For more information, see the Interfacing
Table 14. SPI Timing Diagram Specifications
Name
Description
tDS
Setup time between data and rising edge of SCLK
tDH
Hold time between data and rising edge of SCLK
tCLK
Period of the clock
tS
Setup time between CSB and SCLK
tH
Hold time between CSB and SCLK
tHI
Minimum period that SCLK should be in a logic high state
tLO
Minimum period that SCLK should be in a logic low state
HARDWARE INTERFACE
The pins described in Table 13 comprise the physical interface
between the user’s programming device and the serial port of
the AD9233. The SCLK and CSB pins function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during readback.
The SPI interface is flexible enough to be controlled by either
PROM or PIC microcontrollers. This provides the user with the
ability to use an alternate method to program the ADC. One
method is described in detail in the Application Note AN-812.
When the SPI interface is not used, some pins serve a dual
function. When strapped to AVDD or ground during device
power on, the pins are associated with a specific function.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/DCS and SCLK/DFS pins serve as standalone CMOS-
compatible control pins. When the device is powered up with
the CSB chip select connected to AVDD, the serial port interface is
disabled. In this mode, it is assumed that the user intends to use
the pins as static control lines for the output data format and
duty cycle stabilizer (see Table 10). For more information, see
相关PDF资料 |
PDF描述 |
|---|---|
| LGU2D681MELB | CAP ALUM 680UF 200V 20% SNAP |
| GCM22DRUN | CONN EDGECARD 44POS DIP .156 SLD |
| AD9204-20EBZ | BOARD EVALUATION 20MSPS AD9204 |
| GCM22DRUH | CONN EDGECARD 44POS DIP .156 SLD |
| AD9204-40EBZ | BOARD EVALUATION 40MSPS AD9204 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9233-80EB | 制造商:Analog Devices 功能描述: |
| AD9233-80EBZ | 功能描述:BOARD EVAL FOR AD9233 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| AD9233BCPZ-105 | 功能描述:IC ADC 12BIT 105MSPS 48-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD9233BCPZ-125 | 功能描述:IC ADC 12BIT 80/105/125 48-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD9233BCPZ-80 | 功能描述:IC ADC 12BIT 80MSPS 48-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
发布紧急采购，3分钟左右您将得到回复。