- 您现在的位置：买卖IC网 > PDF目录9158 > AD9516-4BCPZ (Analog Devices Inc)IC CLOCK GEN 1.6GHZ VCO 64-LFCSP PDF资料下载
参数资料
| 型号： | AD9516-4BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/80页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN 1.6GHZ VCO 64-LFCSP |
| 设计资源： | AD9516 Eval Brd Schematic AD9516 Gerber Files |
| 标准包装： | 1 |
| 类型： | 时钟发生器，扇出配送 |
| PLL： | 是 |
| 输入： | 时钟 |
| 输出： | CMOS，LVDS，LVPECL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:14 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 1.8GHz |
| 除法器/乘法器： | 是/无 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 产品目录页面： | 776 (CN2011-ZH PDF) |
| 配用： | AD9516-4/PCBZ-ND - BOARD EVAL FOR AD9516-4 1.8GHZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
Data Sheet
AD9516-4
Rev. C | Page 49 of 80
POWER-DOWN MODES
Chip Power-Down via PD
The AD9516 can be put into a power-down condition by
pulling the PD pin low. Power-down turns off most of the
functions and currents inside the AD9516. The chip remains in
this power-down state until PD is brought back to logic high.
When the AD9516 wakes up, it returns to the settings programmed
into its registers prior to the power-down, unless the registers
are changed by new programming while the PD pin is held low.
The PD power-down shuts down the currents on the chip, except
the bias current that is necessary to maintain the LVPECL
outputs in a safe shutdown mode. This is needed to protect the
LVPECL output circuitry from damage that could be caused by
certain termination and load configurations when tristated.
Because this is not a complete power-down, it can be called
sleep mode.
When the AD9516 is in a PD power-down, the chip is in the
following state:
The PLL is off (asynchronous power-down).
The VCO is off.
The CLK input buffer is off.
All dividers are off.
All LVDS/CMOS outputs are off.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds
to commands.
If the AD9516 clock outputs must be synchronized to each
other, a SYNC is required upon exiting power-down (see the
Synchronizing the Outputs—SYNC Function section). A VCO
calibration is not required when exiting power-down.
PLL Power-Down
The PLL section of the AD9516 can be selectively powered
down. There are three PLL operating modes that are set by
Register 0x010[1:0], as shown in Table 54.
In asynchronous power-down mode, the device powers down
as soon as the registers are updated.
In synchronous power-down mode, the PLL power-down is
gated by the charge pump to prevent unwanted frequency
jumps. The device goes into power-down on the occurrence
of the next charge pump event after the registers are updated.
Distribution Power-Down
The distribution section can be powered down by writing
Register 0x230[1] = 1b. This turns off the bias to the distribution
section. If the LVPECL power-down mode is normal operation
(00b), it is possible for a low impedance load on that LVPECL
output to draw significant current during this power-down.
If the LVPECL power-down mode is set to 11b, the LVPECL
output is not protected from reverse bias and may be damaged
under certain termination conditions.
Individual Clock Output Power-Down
Any of the clock distribution outputs can be powered down
individually by writing to the appropriate registers. The register
map details the individual power-down settings for each output
(see Table 52). The LVDS/CMOS outputs can be powered
down, regardless of their output load configuration.
The LVPECL outputs have multiple power-down modes
(see Table 56), which give some flexibility in dealing with the
various output termination conditions. When the mode is set to
10b, the LVPECL output is protected from reverse bias to
2 VBE + 1 V. If the mode is set to 11b, the LVPECL output is
not protected from reverse bias and can be damaged under
certain termination conditions. This setting also affects the
operation when the distribution block is powered down with
Register 0x230[1] = 1b (see the Distribution Power-Down section).
Individual Circuit Block Power-Down
Other AD9516 circuit blocks (such as CLK, REF1, and REF2)
can be powered down individually. This gives flexibility in
configuring the part for power savings whenever certain chip
functions are not needed.
相关PDF资料 |
PDF描述 |
|---|---|
| V110A48H300BF3 | CONVERTER MOD DC/DC 48V 300W |
| PI3C3126LEX | IC 4-BIT BUS SW 2-PORT 14-TSSOP |
| AD9516-3BCPZ | IC CLOCK PLL/VCO 2GHZ 64LFCSP |
| V110A48H300BF2 | CONVERTER MOD DC/DC 48V 300W |
| PI3C3125LEX | IC 4-BIT BUS SW 2-PORT 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9516-4BCPZ | 制造商:Analog Devices 功能描述:CLOCK GENERATOR, 1.8GHZ, LFCSP-64 |
| AD9516-4BCPZ-REEL7 | 功能描述:IC CLOCK GEN 1.8GHZ VCO 64-LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| AD9516-5 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Output Clock Generator |
| AD9516-5/PCBZ | 功能描述:BOARD EVAL FOR AD9516-5 2.5GHZ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| AD9516-5BCPZ | 功能描述:IC CLOCK GEN W/PLL 64-LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。