- 您现在的位置：买卖IC网 > PDF目录8709 > AD9708ARUZRL7 (Analog Devices Inc)IC DAC 8BIT 100MSPS 28-TSSOP TR PDF资料下载
参数资料
| 型号： | AD9708ARUZRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC DAC 8BIT 100MSPS 28-TSSOP TR |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1,000 |
| 系列： | TxDAC® |
| 设置时间： | 35ns |
| 位数： | 8 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 175mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 125M |
| 配用： | AD9708-EBZ-ND - BOARD EVAL FOR AD9708 |
AD9708
–7–
REV. B
FUNCTIONAL DESCRIPTION
Figure 12 shows a simplified block diagram of the AD9708. The
AD9708 consists of a large PMOS current source array capable of
providing up to 20 mA of total current. The array is divided into
31 equal currents that make up the five most significant bits
(MSBs). The remaining 3 LSBs are also implemented with equally
weighted current sources whose sum total equals 7/8th of an
MSB current source. Implementing the upper and lower bits
with current sources helps maintain the DAC’s high output
impedance (i.e. > 100 k
). All of these current sources are
switched to one or the other of the two output nodes (i.e., IOUTA
or IOUTB) via PMOS differential current switches. The switches
are based on a new architecture that drastically improves
distortion performance.
The analog and digital sections of the AD9708 have separate
power supply inputs (i.e., AVDD and DVDD) that can operate
independently over a 2.7 volt to 5.5 volt range. The digital section,
which is capable of operating up to a 125 MSPS clock rate,
consists of edge-triggered latches and segment decoding logic
circuitry. The analog section includes the PMOS current
sources, the associated differential switches, a 1.20 V bandgap
voltage reference and a reference control amplifier.
The full-scale output current is regulated by the reference con-
trol amplifier and can be set from 2 mA to 20 mA via an exter-
nal resistor, RSET. The external resistor, in combination with
both the reference control amplifier and voltage reference
VREFIO, sets the reference current IREF, which is mirrored over to
the segmented current sources with the proper scaling factor.
The full-scale current, IOUTFS, is thirty-two times the value of IREF.
DAC TRANSFER FUNCTION
The AD9708 provides complementary current outputs, IOUTA
and IOUTB. IOUTA will provide a near full-scale current output,
IOUTFS, when all bits are high (i.e., DAC CODE = 255), while
IOUTB, the complementary output, provides no current. The
current output appearing at IOUTA and IOUTB are a function
of both the input code and IOUTFS and can be expressed as:
IOUTA = (DAC CODE/256)
× I
OUTFS
(1)
IOUTB = (255 – DAC CODE)/256
× I
OUTFS
(2)
where DAC CODE = 0 to 255 (i.e., Decimal Representation).
As previously mentioned, IOUTFS is a function of the reference
current IREF, which is nominally set by a reference voltage
VREFIO and external resistor RSET. It can be expressed as:
IOUTFS = 32
× I
REF
(3)
where
IREF = VREFIO/RSET
(4)
The two current outputs will typically drive a resistive load
directly. If dc coupling is required, IOUTA and IOUTB should
be directly connected to matching resistive loads, RLOAD, which
are tied to analog common, ACOM. Note, RLOAD may repre-
sent the equivalent load resistance seen by IOUTA or IOUTB
as would be the case in a doubly terminated 50
or 75 cable.
The single-ended voltage output appearing at the IOUTA and
IOUTB nodes is simply:
VOUTA = IOUTA
× R
LOAD
(5)
VOUTB = IOUTB
× R
LOAD
(6)
Note the full-scale value of VOUTA and VOUTB should not exceed
the specified output compliance range to maintain specified
distortion and linearity performance.
The differential voltage, VDIFF, appearing across IOUTA and
IOUTB is:
VDIFF = (IOUTA – IOUTB)
× R
LOAD
(7)
Substituting the values of IOUTA, IOUTB, and IREF; VDIFF can be
expressed as:
VDIFF = {(2 DAC CODE – 255)/256}/
× (32 R
LOAD/RSET)
× V
REFIO
(8)
VOLTAGE REFERENCE AND CONTROL AMPLIFIER
The AD9708 contains an internal 1.20 V bandgap reference
that can be easily disabled and overridden by an external refer-
ence. REFIO serves as either an input or output depending on
whether the internal or an external reference is selected. If
REFLO is tied to ACOM, as shown in Figure 13, the internal
reference is activated and REFIO provides a 1.20 V output. In
this case, the internal reference must be compensated externally
with a ceramic chip capacitor of 0.1
F or greater from REFIO
to REFLO. Note that REFIO is not designed to drive any ex-
ternal load. It should be buffered with an external amplifier
having an input bias current less than 100 nA if any additional
loading is required.
+1.20V REF
REFLO
REFIO
FS ADJ
50pF
COMP1
0.1 F
CURRENT
SOURCE
ARRAY
+5V
AVDD
SEGMENTED
SWITCHES
LATCHES
DVDD
DCOM
CLOCK
SLEEP
IOUTA
IOUTB
COMP2
ACOM
0.1 F
+5V
RSET
2k
0.1 F
AD9708
IOUTB
VOUTB
RLOAD
50
VOUTA
RLOAD
50
IOUTA
VDIFF = VOUTA – VOUTB
CLOCK
IREF
VREFIO
DIGITAL DATA INPUTS (DB7–DB0)
Figure 12. Functional Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MPC9456ACR2 | IC CLK BUFF DVDR MUX 1:10 32LQFP |
| AD5444YRM-REEL7 | IC DAC 12BIT MULTIPLYING 10-MSOP |
| AD5647RBRMZ-REEL7 | IC DAC NANO 14BIT DUAL 10-MSOP |
| LTC1426CS8#TR | IC DAC PWM 6BIT DUAL MCPWR 8SOIC |
| AD5341BRUZ-REEL7 | IC DAC 12BIT SNGL VOUT 20-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9708ARZ | 功能描述:IC DAC 8BIT 100MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD9708ARZ | 制造商:Analog Devices 功能描述:IC 8BIT DAC 100MSPS 28SOIC 制造商:Analog Devices 功能描述:IC, 8BIT DAC, 100MSPS, 28SOIC |
| AD9708ARZRL | 功能描述:IC DAC 8BIT 100MSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源 功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-DFN-EP（4x3） 包装:管件 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9708-EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD9708 |
| AD9708-EBZ | 功能描述:BOARD EVAL FOR AD9708 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。