- 您现在的位置：买卖IC网 > PDF目录17056 > AD9714-DPG2-EBZ (Analog Devices Inc)ADC 8BIT DUAL 40LFCSP PDF资料下载
参数资料
| 型号： | AD9714-DPG2-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 43/80页 |
| 文件大小： | 0K |
| 描述： | ADC 8BIT DUAL 40LFCSP |
| 标准包装： | 1 |
| 系列： | TxDAC® |
| DAC 的数量： | 2 |
| 位数： | 8 |
| 采样率（每秒）： | 125M |
| 数据接口： | 串行 |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD9714 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
AD9714/AD9715/AD9716/AD9717
Rev. A | Page 48 of 80
APPLICATIONS INFORMATION
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output confi-
gurations for the AD9714/AD9715/AD9716/AD9717. Unless
otherwise noted, it is assumed that IxOUTFS is set to a nominal
2 mA. For applications requiring the optimum dynamic perfor-
mance, a differential output configuration is suggested. A
differential output configuration can consist of either an
RF transformer or a differential op amp configuration. The
transformer configuration provides the optimum high fre-
quency performance and is recommended for any application
that allows ac coupling. The differential op amp configuration
is suitable for applications requiring dc coupling, signal gain,
and/or a low output impedance.
A single-ended output is suitable for applications in which low
cost and low power consumption are primary concerns.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 103. The
distortion performance of a transformer typically exceeds
that available from standard op amps, particularly at higher
frequencies. Transformer coupling provides excellent rejection
of common-mode distortion (that is, even-order harmonics)
over a wide frequency range. It also provides electrical isolation
and can deliver voltage gain without adding noise. Transformers
with different impedance ratios can also be used for impedance
matching purposes. The main disadvantages of transformer
coupling are low frequency roll-off, lack-of-power gain, and
high output impedance.
AD9714/AD9715/
AD9716/AD9717
IOUTN
IOUTP
29
28
OPTIONAL RDIFF
RLOAD
07
26
5-
0
59
Figure 103. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to a voltage that keeps the voltages on IOUTP and
IOUTN within the output common-mode voltage range of the
device. Note that the dc component of the DAC output current
is equal to IxOUTFS and flows out of both IOUTP and IOUTN.
The center tap of the transformer should provide a path for
this dc current. In most applications, AGND provides the most
convenient voltage for the transformer center tap. The complemen-
tary voltages appearing at IOUTP and IOUTN (that is, VIOUTP
and VIOUTN) swing symmetrically around AGND and should be
maintained with the specified output compliance range of the
AD9714/AD9715/AD9716/AD9717.
A differential resistor, RDIFF, can be inserted in applications
where the output of the transformer is connected to the load,
RLOAD, via a passive reconstruction filter or cable. RDIFF, as
reflected by the transformer, is chosen to provide a source
termination that results in a low voltage standing wave ratio
(VSWR). Note that approximately half the signal power is
dissipated across RDIFF.
SINGLE-ENDED BUFFERED OUTPUT USING
AN OP AMP
An op amp such as the ADA4899-1 can be used to perform
a single-ended current-to-voltage conversion, as shown in
Figure 104. The AD9714/AD9715/AD9716/AD9717 are config-
ured with a pair of series resistors, RS, off each output. For best
distortion performance, RS should be set to 0 Ω. The feedback
resistor, RFB, determines the peak-to-peak signal swing by the
formula
VOUT = RFB × IFS
The common-mode voltage of the output is determined by the
formula
2
1
FS
FB
B
FB
REF
CM
I
R
V
The maximum and minimum voltages out of the amplifier are,
respectively,
B
FB
REF
MAX
R
V
1
VMIN = VMAX – IFS × RFB
+5V
AD9714/AD9715/
AD9716/AD9717
IOUTP
IOUTN 29
RFB
VOUT
REFIO 34
28
RS
AVSS 25
CF
C
RS
RB
07
26
5-
06
0
+
–
ADA4899-1
–5V
Figure 104. Single-Supply Single-Ended Buffer
相关PDF资料 |
PDF描述 |
|---|---|
| EBA15DCBT | CONN EDGECARD 30POS R/A .125 SLD |
| EEM28DTKD | CONN EDGECARD 56POS DIP .156 SLD |
| EBA24DCBN | CONN EDGECARD 48POS R/A .125 SLD |
| EBM11DSEF | CONN EDGECARD 22POS .156 EYELET |
| UBC1H681MNS1MS | CAP ALUM 680UF 50V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9714-EBZ | 制造商:Analog Devices 功能描述:DUAL 8 BIT LOW POWER CONVERTER - Boxed Product (Development Kits) |
| AD9715 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual, 8-/10-/12-/14-Bit Low Power Digital-to-Analog Converters |
| AD9715BCPZ | 功能描述:IC DAC DUAL 10BIT LO PWR 40LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD9715BCPZRL7 | 功能描述:IC DAC DUAL 10BIT LO PWR 40LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 标准包装:47 系列:- 设置时间:2µs 位数:14 数据接口:并联 转换器数目:1 电压电源:单电源 功率耗散（最大）:55µW 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SSOP（0.209"，5.30mm 宽） 供应商设备封装:28-SSOP 包装:管件 输出数目和类型:1 电流，单极；1 电流，双极 采样率（每秒）:* |
| AD9715-DPG2-EBZ | 功能描述:ADC 12BIT DUAL 40LFCSP RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。