参数资料
| 型号： | AD974ANZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/20页 |
| 文件大小： | 0K |
| 描述： | IC DAS 16BIT 4CH 200KSPS 28DIP |
| 标准包装： | 13 |
| 类型： | 数据采集系统（DAS） |
| 分辨率（位）： | 16 b |
| 采样率（每秒）： | 200k |
| 数据接口： | 串行 |
| 电压电源： | 模拟和数字 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 28-PDIP |
| 包装： | 管件 |
| 配用： | EVAL-AD974CB-ND - BOARD EVAL FOR AD974 |
REV. A
AD974
–9–
EXTERNAL DISCONTINUOUS CLOCK DATA READ
DURING CONVERSION WITH NO SYNC OUTPUT
GENERATED
Figure 5 illustrates the method by which data from conversion
“n-1” can be read during conversion “n” while using a discon-
tinuous external clock, without the generation of a SYNC out-
put. After a conversion is initiated, indicated by
BUSY going
low, the result of the previous conversion can be read while
CS
is low and R/
C is high. In this mode CS can be tied low. The
MSB will be valid on the 1st falling edge and the 2nd rising edge of
DATACLK. The LSB will be valid on the 16th falling edge and
the 17th rising edge of DATACLK. A minimum of 16 clock
pulses are required for DATACLK if the receiving device will be
latching data on the falling edge of DATACLK. A minimum of
17 clock pulses are required for DATACLK if the receiving
device will be latching data on the rising edge of DATACLK.
In this mode the data should be clocked out during the first half
of
BUSY so not to degrade conversion performance. This re-
quires use of a 10 MHz DATACLK or greater, with data being
read out as soon as the conversion process begins.
EXTERNAL DISCONTINUOUS CLOCK DATA READ
AFTER CONVERSION WITH SYNC OUTPUT GENERATED
Figure 6 illustrates the method by which data from conver-
sion “n” can be read after the conversion is complete using a
discontinuous external clock, with the generation of a SYNC
output. What permits the generation of a SYNC output is a
transition of DATACLK while either
CS is high or while both
CS and R/C are low. After a conversion is complete, indicated
by
BUSY returning high, the result of that conversion can be
read while
CS is Low and R/C is high. In this mode CS can be
tied low. In Figure 6 clock pulse #0 is used to enable the gen-
eration of a SYNC pulse. The SYNC pulse is actually clocked
out approximately 40 ns after the rising edge of clock pulse #1.
The SYNC pulse will be valid on the falling edge of clock pulse
#1 and the rising edge of clock pulse #2. The MSB will be valid
on the falling edge of clock pulse #2 and the rising edge of clock
pulse #3. The LSB will be valid on the falling edge of clock
pulse #17 and the rising edge of clock pulse #18. The advan-
tage of this method of reading data is that it is not being clocked
out during a conversion and therefore conversion performance is
not degraded.
When reading data after the conversion is complete, with the
highest frequency permitted for DATACLK (15.15 MHz), the
maximum possible throughput is approximately 195 kHz and
not the rated 200 kHz.
EXT
DATACLK
R/
C
BUSY
SYNC
DATA
0
BIT 15
(MSB)
BIT 14
t12
t13
t14
1
2
15
16
t15
t1
t20
t2
t21
t18
BIT 0
(LSB)
t22
Figure 5. Conversion and Read Timing for Reading Previous Conversion Results During a Conversion
Using External Discontinuous Data Clock (EXT/
INT Set to Logic High, CS Set to Logic Low)
EXT
DATACLK
R/
C
BUSY
SYNC
DATA
0
t12
12
3
18
t13
t14
417
t15
t2
t17
t12
t18
BIT 15
(MSB)
BIT 14
BIT 0
(LSB)
Figure 6. Conversion and Read Timing Using An External Discontinuous Data Clock
(EXT/
INT Set to Logic High, CS Set to Logic Low)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B4R-MY-S | CONVERTER MOD DC/DC 7.5V 50W |
| VE-B31-IU | CONVERTER MOD DC/DC 12V 200W |
| VI-B3X-IU | CONVERTER MOD DC/DC 5.2V 200W |
| VI-B4P-MY-S | CONVERTER MOD DC/DC 13.8V 50W |
| MS27473E22A55PA | CONN PLUG 55POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD974AR | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| AD974ARS | 制造商:Analog Devices 功能描述:ADC Single 200ksps 16-bit Serial 28-Pin SSOP 制造商:Rochester Electronics LLC 功能描述:4-CHANNEL 16 BIT 200KSPS DATA ACQ SYSTEM - Bulk |
| AD974ARSZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Data Converter Basics 标准包装:1 系列:- 类型:电机控制 分辨率（位）:12 b 采样率（每秒）:1M 数据接口:串行，并联 电压电源:单电源 电源电压:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:100-TQFP 供应商设备封装:100-TQFP（14x14） 包装:剪切带 (CT) 其它名称:296-18373-1 |
| AD974ARZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Data Converter Basics 标准包装:1 系列:- 类型:电机控制 分辨率（位）:12 b 采样率（每秒）:1M 数据接口:串行，并联 电压电源:单电源 电源电压:2.7 V ~ 3.6 V，4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:100-TQFP 供应商设备封装:100-TQFP（14x14） 包装:剪切带 (CT) 其它名称:296-18373-1 |
| AD974BN | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。