- 您现在的位置：买卖IC网 > PDF目录10977 > AD9833BRMZ-REEL7 (Analog Devices Inc)IC WAVEFORM GEN PROG 10MSOP PDF资料下载
参数资料
| 型号： | AD9833BRMZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 4/24页 |
| 文件大小： | 0K |
| 描述： | IC WAVEFORM GEN PROG 10MSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 1,000 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 25MHz |
| 调节字宽（位）： | 28 b |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
AD9833
Data Sheet
Rev. E | Page 12 of 24
CIRCUIT DESCRIPTION
The AD9833 is a fully integrated direct digital synthesis (DDS)
chip. The chip requires one reference clock, one low precision
resistor, and decoupling capacitors to provide digitally created
sine waves up to 12.5 MHz. In addition to the generation of this
RF signal, the chip is fully capable of a broad range of simple
and complex modulation schemes. These modulation schemes
are fully implemented in the digital domain, allowing accurate
and simple realization of complex modulation algorithms using
DSP techniques.
The internal circuitry of the AD9833 consists of the following
main sections: a numerically controlled oscillator (NCO),
frequency and phase modulators, SIN ROM, a DAC, and a
regulator.
NUMERICALLY CONTROLLED OSCILLATOR PLUS
PHASE MODULATOR
This consists of two frequency select registers, a phase accumulator,
two phase offset registers, and a phase offset adder. The main
component of the NCO is a 28-bit phase accumulator. Continuous
time signals have a phase range of 0 to 2π. Outside this range of
numbers, the sinusoid functions repeat themselves in a periodic
manner. The digital implementation is no different. The
accumulator simply scales the range of phase numbers into a
multibit digital word. The phase accumulator in the AD9833 is
implemented with 28 bits. Therefore, in the AD9833, 2π = 228.
Likewise, the ΔPhase term is scaled into this range of numbers:
0 < ΔPhase < 228 1
With these substitutions, the previous equation becomes
f = ΔPhase × fMCLK∕228
where 0 < ΔPhase < 228 1.
The input to the phase accumulator can be selected from either
the FREQ0 register or the FREQ1 register and is controlled by
the FSELECT bit. NCOs inherently generate continuous phase
signals, thus avoiding any output discontinuity when switching
between frequencies.
Following the NCO, a phase offset can be added to perform
phase modulation using the 12-bit phase registers. The contents
of one of these phase registers are added to the most significant
bits of the NCO. The AD9833 has two phase registers; their
resolution is 2π/4096.
SIN ROM
To make the output from the NCO useful, it must be converted
from phase information into a sinusoidal value. Because phase
information maps directly into amplitude, the SIN ROM uses the
digital phase information as an address to a lookup table and
converts the phase information into amplitude. Although the NCO
contains a 28-bit phase accumulator, the output of the NCO is
truncated to 12 bits. Using the full resolution of the phase
accumulator is impractical and unnecessary, because this would
require a lookup table of 228 entries. It is necessary only to have
sufficient phase resolution such that the errors due to truncation
are smaller than the resolution of the 10-bit DAC. This requires
that the SIN ROM have two bits of phase resolution more than
the 10-bit DAC.
The SIN ROM is enabled using the mode bit (D1) in the control
register (see Table 15).
DIGITAL-TO-ANALOG CONVERTER (DAC)
The AD9833 includes a high impedance, current source 10-bit
DAC. The DAC receives the digital words from the SIN ROM
and converts them into the corresponding analog voltages.
The DAC is configured for single-ended operation. An external
load resistor is not required because the device has a 200
resistor on board. The DAC generates an output voltage of
typically 0.6 V p-p.
REGULATOR
VDD provides the power supply required for the analog section
and the digital section of the AD9833. This supply can have a
value of 2.3 V to 5.5 V.
The internal digital section of the AD9833 is operated at 2.5 V.
An on-board regulator steps down the voltage applied at VDD
to 2.5 V. When the applied voltage at the VDD pin of the AD9833
is less than or equal to 2.7 V, the CAP/2.5V and VDD pins
should be tied together, thus bypassing the on-board regulator.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1D-IW-B1 | CONVERTER MOD DC/DC 85V 100W |
| MCF51AC256BCFUE | MCU 32BIT 256K FLASH 64-QFP |
| AD9833BRMZ-REEL | IC WAVEFORM GEN PROG 10MSOP |
| MCF51AC128ACPUE | MCU 32BIT 128K FLASH CAN 64-LQFP |
| VE-B1B-IX-B1 | CONVERTER MOD DC/DC 95V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9833SRMZ-EP-RL7 | 制造商:Analog Devices 功能描述:10 bit 10 pin DDS I.C. |
| AD9833WBRMZ-REEL | 制造商:Analog Devices 功能描述:10 BIT, 10 PIN DDS I.C. - Tape and Reel |
| AD9834 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, +2.3 V to +5.5 V, 50 MHz Complete DDS |
| AD9834_10 | 制造商:AD 制造商全称:Analog Devices 功能描述:20 mW Power, 2.3 V to 5.5 V,75 MHz Complete DDS |
| AD9834BRU | 功能描述:IC DDS W/COMP 2.3V 50MHZ 20TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。