- 您现在的位置：买卖IC网 > PDF目录10978 > AD9834BRUZ-REEL7 (Analog Devices Inc)IC DDS 10BIT 50MHZ LP 20TSSOP PDF资料下载
参数资料
| 型号： | AD9834BRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/32页 |
| 文件大小： | 0K |
| 描述： | IC DDS 10BIT 50MHZ LP 20TSSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 设计资源： | Amplitude Control Circuit for AD9834 Waveform Generator (CN0156) |
| 标准包装： | 1,000 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 50MHz |
| 调节字宽（位）： | 28 b |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD9834
Data Sheet
GROUNDING AND LAYOUT
The printed circuit board (PCB) that houses the AD9834 should
be designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can easily be separated. A minimum
etch technique is generally best for ground planes because it
gives the best shielding. Digital and analog ground planes
should only be joined in one place. If the AD9834 is the only
device requiring an AGND-to-DGND connection, the ground
planes should be connected at the AGND and DGND pins of
the AD9834. If the AD9834 is in a system where multiple devices
require AGND-to-DGND connections, the connection should
be made at one point only, establishing a star ground point as
close as possible to the AD9834.
Avoid running digital lines under the device because these
couple noise onto the die. The analog ground plane should be
allowed to run under the AD9834 to avoid noise coupling. The
power supply lines to the AD9834 should use as large a track as
possible to provide low impedance paths and reduce the effects
of glitches on the power supply line. Fast switching signals, such
as clocks, should be shielded with digital ground to avoid radiating
noise to other sections of the board. Avoid crossover of digital
and analog signals. Traces on opposite sides of the board should
run at right angles to each other to reduce the effects of feed-
through through the board. A microstrip technique is by far the
best, but it is not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes and signals are placed on the other side.
Good decoupling is important. The analog and digital supplies
to the AD9834 are independent and separately pinned out to
minimize coupling between analog and digital sections of the
device. All analog and digital supplies should be decoupled to
AGND and DGND, respectively, with 0.1 μF ceramic capacitors
in parallel with 10 μF tantalum capacitors. To achieve the best
performance from the decoupling capacitors, they should be
placed as close as possible to the device, ideally right up against
the device. In systems where a common supply is used to drive
both the AVDD and DVDD of the AD9834, it is recommended
that the system’s AVDD supply be used. This supply should have
the recommended analog supply decoupling between the AVDD
pins of the AD9834 and AGND, and the recommended digital
supply decoupling capacitors between the DVDD pins and DGND.
Proper operation of the comparator requires good layout strategy.
The strategy must minimize the parasitic capacitance between
VIN and the SIGN BIT OUT pin by adding isolation using a
ground plane. For example, in a multilayered board, the VIN
signal could be connected to the top layer, and the SIGN BIT OUT
could be connected to the bottom layer so that isolation is
provided by the power and ground planes between them.
Rev. D | Page 26 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1H-IW-B1 | CONVERTER MOD DC/DC 52V 100W |
| VE-B1F-IX-B1 | CONVERTER MOD DC/DC 72V 75W |
| MCF51AC256BCPUE | MCU 32BIT 256K FLASH 64-LQFP |
| AD9834BRUZ-REEL | IC DDS 10BIT 50MHZ LP 20TSSOP |
| MCF51EM256CLK | IC MCU 32BIT 256KB FLASH 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9834CRUZ | 功能描述:IC DDS 10BIT 75MHZ LP 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD9834CRUZ-REEL7 | 功能描述:IC DDS 10BIT 75MHZ LP 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD9835 | 制造商:AD 制造商全称:Analog Devices 功能描述:50 MHz CMOS Complete DDS |
| AD9835BRU | 功能描述:IC DDS DAC 10BIT 50MHZ 16-TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD9835BRU-REEL | 制造商:Analog Devices 功能描述:Direct Digital Synthesizer 50MHz 1-DAC 10-Bit Serial 16-Pin TSSOP T/R 制造商:Analog Devices 功能描述:DGTL SYNTHESIZER 16TSSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。