- 您现在的位置：买卖IC网 > PDF目录8586 > ADA4432-1BCPZ-R7 (Analog Devices Inc)IC SD VIDEO FILTER AMP 8LFCSP PDF资料下载
参数资料
| 型号： | ADA4432-1BCPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/29页 |
| 文件大小： | 0K |
| 描述： | IC SD VIDEO FILTER AMP 8LFCSP |
| 标准包装： | 1 |
| 应用： | 车载系统 |
| 输出类型： | 单端 |
| 电路数： | 1 |
| -3db带宽： | 10.5MHz |
| 电流 - 电源： | 7.6mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 2.6 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 8-LFCSP-WD（3x3） |
| 包装： | 标准包装 |
| 其它名称： | ADA4432-1BCPZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Data Sheet
ADA4432-1/ADA4433-1
Rev. A | Page 17 of 28
APPLICATIONS INFORMATION
METHODS OF TRANSMISSION
Pseudo Differential Mode (Unbalanced Source
Termination)
The ADA4432-1 can be used as a pseudo differential driver
with an unbalanced transmission line. Pseudo differential mode
uses a single conductor to carry an unbalanced data signal from
the driver to the receiver, while a second conductor is used as a
ground reference signal.
The positive conductor connects the ADA4432-1 output to the
positive input of a differential receiver, such as ADA4830-1. The
negative wire or ground conductor from the source circuitry
connects to the negative input of the receiver. Match the impedance
of the input termination at the receiver to the output termination
of the ADA4432-1 (see Figure 43).
Figure 43. Pseudo Differential Mode
Pseudo Differential Mode (Balanced Source Impedance)
Pseudo differential signaling is typically implemented using
unbalanced source termination, as shown in Figure 43. With this
arrangement, however, common-mode signals on the positive
and negative inputs receive different attenuation due to unbalanced
termination at the source. This effectively converts some of the
common-mode signal into a differential mode signal, degrading
the overall common-mode rejection of the system. System
common-mode rejection can be improved by balancing the output
impedance of the driver, as shown in Figure 44. Splitting the source
termination resistance evenly between the hot and cold conductors
results in matched attenuation of the common-mode signals,
ensuring maximum rejection.
Figure 44. Pseudo Differential Mode with Balanced Source Impedance
Fully Differential Mode
The ADA4433-1 is designed to be used as a fully differential driver.
The differential outputs of the ADA4433-1 allow fully balanced
transmission using twisted or untwisted pair cable. In this
configuration, the differential output termination consists of two
source resistors, one on each output, and each equal to half the
receiver input termination. For example, in a 75 system, each
output of the ADA4433-1 is back terminated with 37.5 resistors
that are connected to a differential resistance of 75 at the receiver.
An illustration of this arrangement is shown in Figure 45.
Figure 45. Fully Differential Mode
PRINTED CIRCUIT BOARD (PCB) LAYOUT
As with all high speed applications, attention to PCB layout is of
paramount importance. Adhere to standard high speed layout
practices when designing with the ADA4432-1 and ADA4433-1.
A solid ground plane is recommended. Place a 0.1 F surface-
mount, ceramic power supply decoupling capacitor as close as
possible to the supply pin.
Connect the GND pin(s) to the ground plane with a trace that is
as short as possible. Use controlled impedance traces of the shortest
length possible to connect to the signal I/O pins and do not run the
traces over any voids in the ground plane. A 75 impedance level
is typically used in video applications. All signal outputs of the
ADA4432-1 and ADA4433-1 should include series termination
resistors when driving transmission lines.
When the ADA4432-1 or the ADA4433-1 receives its inputs from a
device with current outputs, the required load resistor value for
the output current is most often different from the characteristic
impedance of the signal traces. In this case, if the interconnections
are sufficiently short (less than 2 inches), the trace does not
need to be terminated in its characteristic impedance.
INN
INP
ADA4830-1
75
+
75
POSITIVE WIRE
NEGATIVE WIRE
DRIVER PCB
ADA4432-1
10597-
025
INN
INP
ADA4830-1
75
+
37.5
37.5
POSITIVE WIRE
NEGATIVE WIRE
DRIVER PCB
ADA4432-1
10597-
026
INN
INP
ADA4830-1
75
+
37.5
37.5
POSITIVE WIRE
NEGATIVE WIRE
DRIVER PCB
ADA4433-1
10597-
027
相关PDF资料 |
PDF描述 |
|---|---|
| AD5541AR | IC DAC 16BIT SRL IN/VOUT 8-SOIC |
| AD767JP | IC DAC 12BIT W/AMP 28-PLCC |
| AD7245JP | IC DAC 12BIT LC2MOS 28-PLCC |
| VE-2W0-IV-F2 | CONVERTER MOD DC/DC 5V 150W |
| AD7245AAP | IC DAC 12BIT W/REF 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4432-1BRJ-EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:SD Video Filter Amplifiers |
| ADA4432-1BRJZ-R2 | 制造商:Analog Devices 功能描述:HIGH SPEED VIDEO FILTER AMPLIFIERS - Tape and Reel |
| ADA4432-1BRJZ-R7 | 功能描述:IC SD VIDEO FILTER AMP SOT23-6 RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ADA4432-1WBCPZ-R7 | 制造商:AD 制造商全称:Analog Devices 功能描述:SD Video Filter Amplifiers |
| ADA4432-1WBRJZ-R2 | 功能描述:IC SD VIDEO FILTER AMP 6SOT23 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:过期 应用:车载系统 输出类型:单端 电路数:1 -3db 带宽:10.5MHz 压摆率:- 电流 - 电源:7.6mA 电流 - 输出/通道:50mA 电压 - 电源，单/双（±）:2.6 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商器件封装:SOT-23 标准包装:250 |
发布紧急采购，3分钟左右您将得到回复。