- 您现在的位置：买卖IC网 > PDF目录16955 > ADA4932-1YCP-EBZ (Analog Devices Inc)BOARD EVAL FOR ADA4932-1YCP PDF资料下载
参数资料
| 型号： | ADA4932-1YCP-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADA4932-1YCP |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 放大器类型： | 差分 |
| 板类型： | 裸（未填充） |
| 已供物品： | 板 |
| 已用 IC / 零件： | 16-LFCSP 封装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Data Sheet
ADA4932-1/ADA4932-2
Similar to the case of a conventional op amp, the output noise
voltage densities can be estimated by multiplying the input-
referred terms at +IN and IN by the appropriate output factor,
where:
(
)
2
1
N
β
G
+
=
2
is the circuit noise gain.
G1
F1
G1
1
R
β
+
=
and
G2
F2
G2
2
R
β
+
=
are the feedback factors.
When the feedback factors are matched, RF1/RG1 = RF2/RG2, β1 =
β2 = β, and the noise gain becomes
G
F
N
R
β
G
+
=
1
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sum-
square of the individual output noise terms.
∑
=
8
1
i
2
nOi
nOD
v
Table 12 and Table 13 list several common gain settings,
associated resistor values, input impedance, and output noise
density for both balanced and unbalanced input configurations.
IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
The gain from the VOCM pin to VOUT,dm is equal to
2(β1 β2)/(β1 + β2)
When β1 = β2, this term goes to zero and there is no differential
output voltage due to the voltage on the VOCM input (including
noise). The extreme case occurs when one loop is open and the
other has 100% feedback; in this case, the gain from VOCM input
to VOUT,dm is either +2 or 2, depending on which loop is closed.
The feedback loops are nominally matched to within 1% in
most applications, and the output noise and offsets due to the
VOCM input are negligible. If the loops are intentionally mismatched
by a large amount, it is necessary to include the gain term from
VOCM to VOUT,dm and account for the extra noise. For example, if
β1 = 0.5 and β2 = 0.25, the gain from VOCM to VOUT,dm is 0.67. If
the VOCM pin is set to 2.5 V, a differential offset voltage is present at
the output of (2.5 V)(0.67) = 1.67 V. The differential output noise
contribution is (9.6 nV/√Hz)(0.67) = 6.4 nV/√Hz. Both of these
results are undesirable in most applications; therefore, it is best
to use nominally matched feedback factors.
Mismatched feedback networks also result in a degradation of
the ability of the circuit to reject input common-mode signals,
much the same as for a four-resistor difference amplifier made
from a conventional op amp.
As a practical summarization of the above issues, resistors of 1%
tolerance produce a worst-case input CMRR of approximately
40 dB, a worst-case differential-mode output offset of 25 mV
due to a 2.5 V VOCM input, negligible VOCM noise contribution,
and no significant degradation in output balance error.
CALCULATING THE INPUT IMPEDANCE FOR AN
APPLICATION CIRCUIT
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
(+DIN and DIN) is RIN,dm = RG + RG = 2 × RG.
+VS
–VS
+IN
–IN
RF
+DIN
–DIN
VOCM
RG
VOUT, dm
07752-
048
ADA4932-x
Figure 57. ADA4932-x Configured for Balanced (Differential) Inputs
For an unbalanced, single-ended input signal (see Figure 58),
the input impedance is
(
)
+
×
=
F
G
F
G
se
IN
R
2
1
,
ADA4932-x
RL VOUT, dm
+VS
–VS
RG
RF
VOCM
RIN, se
07752-
049
Figure 58. ADA4932-x with Unbalanced (Single-Ended) Input
The input impedance of the circuit is effectively higher than it is
for a conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor, RG. The common-mode voltage at the
amplifier input terminals can be easily determined by noting that
the voltage at the inverting input is equal to the noninverting
output voltage divided down by the voltage divider that is formed
by RF and RG in the lower loop. This voltage is present at both
input terminals due to negative voltage feedback and is in phase
Rev. C | Page 21 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ADA4950-1YCP-EBZ | BOARD EVAL FOR ADA4950-1YCP |
| LLS2W221MELC | CAP ALUM 220UF 450V 20% SNAP |
| 222D132-4-60/42-0 | BOOT MOLDED |
| ECM18DRKI-S13 | CONN EDGECARD 36POS .156 EXTEND |
| 222D132-3-60/42-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4932-1YCPZ-R2 | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 制造商:Analog Devices 功能描述:LW CST/LW PWR DIFF ADC DRIVER - Tape and Reel 制造商:Analog Devices 功能描述:ANAADA4932-1YCPZ-R2 LW CST/LW PWR DIFF A 制造商:Analog Devices 功能描述:AMP DIFF LP 80MA 16LFCSP 制造商:Analog Devices 功能描述:AMP, DIFF, LP, 80MA, 16LFCSP 制造商:Analog Devices 功能描述:AMP, DIFF, LP, 80MA, 16LFCSP; No. of Amplifiers:1; Input Offset Voltage:2.2mV; Bandwidth:560MHz; Amplifier Case Style:LFCSP; No. of Pins:16; Supply Voltage Range:3V to 11V; Slew Rate:2800V/s; Supply Current:9.6mA; Operating ;RoHS Compliant: Yes 制造商:Analog Devices 功能描述:SP Amp Diff ADC Driver Single 5.5V/11V |
| ADA4932-1YCPZ-R2 | 制造商:Analog Devices 功能描述:IC DIFF AMP 560MHZ 2800V/ LFCSP-16 |
| ADA4932-1YCPZ-R21 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power Differential ADC Driver |
| ADA4932-1YCPZ-R7 | 功能描述:IC AMP DIFF LP 80MA 16LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| ADA4932-1YCPZ-R71 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power Differential ADC Driver |
发布紧急采购，3分钟左右您将得到回复。