参数资料
| 型号： | ADA4932-1YCPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/29页 |
| 文件大小： | 0K |
| 描述： | IC AMP DIFF LP 80MA 16LFCSP |
| 设计资源： | Single-Ended-to-Differential High Speed Drive Circuit for 16-Bit, 10 MSPS AD7626 ADC (CN0105) |
| 标准包装： | 5,000 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 2800 V/µs |
| -3db带宽： | 560MHz |
| 电流 - 输入偏压： | 2.5µA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 9.6mA |
| 电流 - 输出 / 通道： | 80mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 11 V，±1.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-VQ |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Data Sheet
ADA4932-1/ADA4932-2
4. The feedback resistor value is modified as a final gain
adjustment to obtain the desired output voltage.
To make the output voltage VOUT = 1 V p-p, calculate RF
using the following formula:
(
)(
) (
)(
)
=
=
+
=
509
03
.
1
5
.
524
1
,
p
V
p
V
R
V
Desired
R
TH
TS
G
dm
OUT
F
The closest standard 1% value to 509 is 511 , which
gives a differential output voltage of 1.00 V p-p.
The final circuit is shown in Figure 63.
ADA4932-x
RL
VOUT, dm
1.00V p-p
+VS
–VS
RS
50
RG
499
RG
499
RF
511
RF
511
VOCM
VS
2V p-p
1V p-p
RT
53.6
RTS
25.5
07752-
054
Figure 63. Terminated Single-Ended-to-Differential System with G = 2
INPUT COMMON-MODE VOLTAGE RANGE
The ADA4932-x input common-mode range is shifted down
by approximately one VBE, in contrast to other ADC drivers
with centered input ranges such as the ADA4939-x. The
downward-shifted input common-mode range is especially
suited to dc-coupled, single-ended-to-differential, and single-
supply applications.
For ±5 V operation, the input common-mode range at the
summing nodes of the amplifier is specified as 4.8 V to +3.2 V,
and is specified as +0.2 V to +3.2 V with a +5 V supply. To
avoid nonlinearities, the voltage swing at the +IN and IN
terminals must be confined to these ranges.
INPUT AND OUTPUT CAPACITIVE AC COUPLING
While the ADA4932-x is best suited to dc-coupled applications,
it is nonetheless possible to use it in ac-coupled circuits. Input
ac coupling capacitors can be inserted between the source and
RG. This ac coupling blocks the flow of the dc common-mode
feedback current and causes the ADA4932-x dc input common-
mode voltage to equal the dc output common-mode voltage.
These ac coupling capacitors must be placed in both loops to keep
the feedback factors matched. Output ac coupling capacitors can
be placed in series between each output and its respective load.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
tage divider comprised of two 50 k resistors across the supplies,
with a tap at a voltage approximately equal to the midsupply
point, [(+VS) + (VS)]/2. Because of this internal divider, the
VOCM pin sources and sinks current, depending on the externally
applied voltage and its associated source resistance. Relying on
the internal bias results in an output common-mode voltage
that is within about 100 mV of the expected value.
In cases where more accurate control of the output common-
mode level is required, it is recommended that an external
source or resistor divider be used with source resistance less
than 100 . If an external voltage divider consisting of equal
resistor values is used to set VOCM to midsupply with greater
accuracy than produced internally, higher values can be used
because the external resistors are placed in parallel with the
internal resistors. The output common-mode offset listed in the
low impedance voltage source.
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC; however, care must be taken to
ensure that the output has sufficient drive capability. The input
impedance of the VOCM pin is approximately 10 k. If multiple
ADA4932-x devices share one ADC reference output, a buffer
may be necessary to drive the parallel inputs.
Rev. C | Page 23 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ADA4939-2YCPZ-R7 | IC AMP DIFF DUAL ULDIST 24LFCSP |
| ADA4940-1ARZ-R7 | IC DIFF ADC DVR 18BIT LN 8SOIC |
| ADA4950-1YCPZ-RL | IC AMP DIFF LP 114MA 16LFCSP |
| ADEL2020ARZ-20-RL | IC OPAMP CF LN LP 60MA 20SOIC |
| ADL5561ACPZ-R7 | IC AMP DIFF RF/IF 2.9GHZ 16LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADA4932-1YCPZ-RL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power Differential ADC Driver |
| ADA4932-2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power Differential ADC Driver |
| ADA4932-2YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4932-2YCP RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ADA4932-2YCPZ-R2 | 功能描述:IC AMP DIFF DUAL LP 80MA 24LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| ADA4932-2YCPZ-R2 | 制造商:Analog Devices 功能描述:IC DIFF AMP 560MHZ 2800V/ LFCSP-16 |
发布紧急采购，3分钟左右您将得到回复。