- 您现在的位置：买卖IC网 > PDF目录10253 > ADAU1702JSTZ (Analog Devices Inc)IC AUDIO PROC 2ADC/4DAC 48-LQFP PDF资料下载
参数资料
| 型号： | ADAU1702JSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/52页 |
| 文件大小： | 0K |
| 描述： | IC AUDIO PROC 2ADC/4DAC 48-LQFP |
| 标准包装： | 1 |
| 系列： | SigmaDSP® |
| 类型： | 音频处理器 |
| 应用： | 车载，监视器，MP3 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
| 产品目录页面： | 776 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADAU1702
Rev. C | Page 30 of 52
RAMS AND REGISTERS
Table 19. RAM Map and Read/Write Modes
Memory
Size
Address Range
Read
Write
Write Modes
Parameter RAM
1024 × 32
0 to 1023 (0x0000 to 0x03FF)
Yes
Direct write 1 safeload write
Program RAM
512 × 40
1024 to 1535 (0x0400 to 0x05FF)
Yes
Direct write1
Reserved
Not applicable
1536 to 2047 (0x0600 to 0x07FF) 2
No
Not applicable
1 Internal registers should be cleared first to avoid clicks/pops.
2 Addresses 1536 to 2047 (0x0600 to 0x07FF) are reserved RAM locations and data cannot be written to them.
ADDRESS MAPS
ADAU1702 register map. The address space encompasses a
set of registers and two RAMs: one holds signal processing
parameters and the other holds the program instructions. The
program RAM and parameter RAM are initialized on power-up
from on-board boot ROMs (see the Power-Up Sequence section).
All RAMs and registers have a default value of all 0s, except for
the program RAM, which is loaded with the default program
(see the Initialization section).
PARAMETER RAM
The parameter RAM is 32 bits wide and occupies Address 0
to Address 1023. Each parameter is padded with four 0s before
the MSB to extend the 28-bit word to a full 4-byte width. The
parameter RAM is initialized to all 0s on power-up. The data
format of the parameter RAM is twos complement, 5.23.
This means that the coefficients can range from +16.0 (minus
1 LSB) to 16.0, with 1.0 represented by the binary word,
0000 1000 0000 0000 0000 0000 0000, or by the hexadecimal
word, 0x00 0x80 0x00 0x00.
The parameter RAM can be written using one of the two
following methods: a direct read/write or a safeload write.
Direct Read/Write
The direct read/write method allows direct access to the program
RAM and parameter RAM. This mode of operation is typically
used when loading a new RAM using burst mode addressing. The
clear registers bit in the core control register should be set to 0
using this mode to prevent any clicks or pops in the outputs. Note
that this mode can be used during live program execution, but
because there is no handshaking between the core and the control
port, the parameter RAM is unavailable to the DSP core during
control writes, resulting in clicks and pops in the audio stream.
Safeload Write
Up to five safeload registers can be loaded with the parameter
RAM address and data. The data is then transferred to the
requested address when the RAM is not busy. This method can
be used for dynamic updates while live program material is
playing through the ADAU1702. For example, a complete
update of one biquad section can occur in one audio frame
while the RAM is not busy. This method is not available for
writing to the program RAM or control registers.
DATA RAM
The ADAU1702 data RAM is used to store audio data-words for
processing. For the most part, this process is transparent to the
user. The user cannot address this RAM space, which has a size
of 0.5k words, directly from the control port.
Data RAM utilization should be considered when implementing
blocks that require large amounts of data RAM space, such as
delays. The SigmaDSP core processes delay times in one sample
increments; therefore, the total pool of delay available to the user
equals 512 multiplied by the sample period. For a fS of 48 kHz,
the pool of available delay is a maximum of about 10 ms. In
practice, this much data memory is not available to the user
because every block in a design uses a few data memory locations
for its processing. In most DSP programs, this does not signifi-
cantly impact the total delay time. The SigmaStudio compiler
manages the data RAM and indicates if the number of addresses
needed in the design exceeds the maximum available.
READ/WRITE DATA FORMATS
The read/write formats of the control port are designed to
be byte oriented. This allows easy programming of common
microcontroller chips. To fit into a byte oriented format, 0s are
appended to the data fields before the MSB to extend the data-
word to eight bits. For example, 28-bit words written to the
parameter RAM are appended with four leading 0s to equal
32 bits (four bytes); 40-bit words written to the program RAM
are not appended with 0s because they are already a full five bytes.
These zero padded data fields are appended to a 3-byte field
consisting of a 7-bit chip address, a read/write bit, and an 11-bit
RAM/register address. The control port knows how many data
bytes to expect based on the address given in the first three bytes.
The total number of bytes for a single location write command
can vary from four bytes (for a control register write) to eight
bytes (for a program RAM write). Burst mode can be used to fill
contiguous register or RAM locations. A burst mode write begins
by writing the address and data of the first RAM or register location
to be written. Rather than ending the control port transaction
(by issuing a stop command in I2C mode or by bringing the
CLATCH signal high in SPI mode after the data-word), as is
done in a single address write, the next data-word can be
immediately written without specifying its address. The
ADAU1702 control port auto-increments the address of each write
even across the boundaries of the different RAMs and registers.
相关PDF资料 |
PDF描述 |
|---|---|
| CS8406-CSZ | IC XMITTER DGTL 192KHZ 28SOIC |
| 14281-18PG-3ES | CONN RCPT 18POS PNL MNT PIN |
| AD7708BRU | IC ADC 16BIT R-R 8/10CH 28-TSSOP |
| MS3106F20-29PW | CONN PLUG 17POS STRAIGHT W/PINS |
| MS3106F20-29P | CONN PLUG 17POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADAU1702JSTZ-RL | 功能描述:IC AUDIO PROC 2ADC/4DAC 48-LQFP RoHS:是 类别:集成电路 (IC) >> 线性 - 音频处理 系列:SigmaDSP® 其它有关文件:STA321 View All Specifications 标准包装:1 系列:Sound Terminal™ 类型:音频处理器 应用:数字音频 安装类型:表面贴装 封装/外壳:64-LQFP 裸露焊盘 供应商设备封装:64-LQFP EP（10x10） 包装:Digi-Reel® 其它名称:497-11050-6 |
| ADAU1761 | 制造商:AD 制造商全称:Analog Devices 功能描述:SigmaDSP Stereo, Low Power, 96 kHz, 24-Bit Audio Codec with Integrated PLL |
| ADAU1761BCPZ | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 编解码器 系列:SigmaDSP® 标准包装:2,500 系列:- 类型:PCM 数据接口:PCM 音频接口 分辨率（位）:15 b ADC / DAC 数量:1 / 1 三角积分调变:是 S/N 比，标准 ADC / DAC (db):- 动态范围，标准 ADC / DAC (db):- 电压 - 电源，模拟:2.7 V ~ 3.3 V 电压 - 电源，数字:2.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-VFBGA 供应商设备封装:80-BGA MICROSTAR JUNIOR（5x5） 包装:带卷 (TR) 其它名称:296-21257-2 |
| ADAU1761BCPZ | 制造商:Analog Devices 功能描述:IC, AUDIO CODEC, 24BIT, 96KHZ, LFCSP-32 |
| ADAU1761BCPZ-R7 | 功能描述:IC SIGMADSP CODEC PLL 32LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 编解码器 系列:SigmaDSP® 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率（位）:18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比，标准 ADC / DAC (db):81.5 / 88 动态范围，标准 ADC / DAC (db):82 / 87.5 电压 - 电源，模拟:2.6 V ~ 3.3 V 电压 - 电源，数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP（7x7） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。