- 您现在的位置：买卖IC网 > Datasheet目录307 > ADD5203ACPZ-RL (Analog Devices Inc)IC LED DRVR WHITE BCKLGT 28LFCSP Datasheet资料下载
参数资料
| 型号： | ADD5203ACPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT 28LFCSP |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 350kHz ~ 1MHz |
| 电源电压： | 6 V ~ 21 V |
| 输出电压： | 45V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-WQ（4x4） |
| 包装： | 标准包装 |
| 工作温度： | -25°C ~ 85°C |
| 其它名称： | ADD5203ACPZ-RLDKR |
ADD5203
EXTERNAL COMPONENT SELECTION GUIDE
Inductor Selection
The inductor is an integral part of the step-up converter. It stores
energy during the switch-on time and transfers that energy to
the output through the output diode during the switch-off time.
An inductor in the range of 4.7 μH to 22 μH is recommended.
In general, lower inductance values result in higher saturation
current and lower series resistance for a given physical size.
However, lower inductance results in higher peak current, which
can lead to reduced efficiency and greater input and/or output
ripple and noise. Peak-to-peak inductor ripple current at close
to 30% of the maximum dc input current typically yields an
optimal compromise.
The input (V IN ) and output (V OUT ) voltages determine the
switch duty cycle (D), which in turn can be used to determine
are preferred because of their low ESR characteristics.
Alternatively, use a high value, medium ESR capacitor in
parallel with a 0.1 μF low ESR capacitor as close as possible to
the ADD5203.
The output capacitor maintains the output voltage and supplies
current to the load while the ADD5203 switch is on. The value
and characteristics of the output capacitor greatly affect the
output voltage ripple and stability of the regulator. Use a low
ESR output capacitor; ceramic dielectric capacitors are preferred.
For very low ESR capacitors, such as ceramic capacitors, the
ripple current due to the capacitance is calculated as follows.
Because the capacitor discharges during the on time (t ON ), the
charge removed from the capacitor (Q C ) is the load current
multiplied by the on time. Therefore, the output voltage ripple
(ΔV OUT ) is
V OUT ? V IN
the inductor ripple current.
D =
V OUT
Δ V OUT =
where:
Q C
C OUT
=
I L × t ON
C OUT
Use the duty cycle and switching frequency (f SW ) to determine
the on time.
C OUT is the output capacitance.
I L is the average inductor current.
t ON =
D
f SW
Using the duty cycle and switching frequency (f SW ), users can
determine the on time with the following equation:
V × t ON
V IN × t ON
t ON =
V OUT ? V IN
I L × ( V OUT ? V IN )
f SW × V OUT × Δ V OUT
The inductor ripple current (ΔI L ) in a steady state is
Δ I L = IN
L
Solve for the inductance value (L).
L =
Δ I L
Make sure that the peak inductor current (that is, the maximum
input current plus half of the inductor ripple current) is less
than the rated saturation current of the inductor. In addition,
ensure that the maximum rated rms current of the inductor is
greater than the maximum dc input current to the regulator.
For duty cycles greater than 50% that occur with input voltages
greater than half the output voltage, slope compensation is required
to maintain stability of the current-mode regulator. The inherent
open-loop stability causes subharmonic instability when the
duty ratio is greater than 50%. To avoid subharmonic instability,
the slope of the inductor current should be less than half of the
compensation slope.
Inductor manufacturers include Coilcraft, Inc., Sumida
Corporation, and Toko.
Input and Output Capacitors Selection
The ADD5203 requires input and output bypass capacitors to
supply transient currents while maintaining a constant input
and output voltage. Use a low effective series resistance (ESR)
10 μF or greater capacitor for the input capacitor to prevent noise
at the ADD5203 input. Place the input between the VIN and
GND, as close as possible to the ADD5203. Ceramic capacitors
D
f SW
The input (V IN ) and output (V OUT ) voltages determine the
switch duty cycle (D) with the following equation:
D =
V OUT
Choose the output capacitor based on the following equation:
C OUT ≥
Capacitor manufacturers include Murata Manufacturing Co.,
Ltd., AVX, Sanyo, and Taiyo Yuden Co., Ltd.
Diode Selection
The output diode conducts the inductor current to the output
capacitor and loads while the switch is off. For high efficiency,
minimize the forward voltage drop of the diode. Schottky diodes
are recommended. However, for high voltage, high temperature
applications, where the Schottky diode reverse leakage current
becomes significant and can degrade efficiency, use an ultrafast
junction diode. The output diode for a boost regulator must be
chosen depending on the output voltage and the output current.
The diode must be rated for a reverse voltage equal to or greater
than the output voltage used. The average current rating must
be greater than the maximum load current expected, and the peak
current rating must be greater than the peak inductor current.
Using Schottky diodes with lower forward voltage drop decreases
power dissipation and increases efficiency. The diode must be
rated to handle the average output load current. Many diode
Rev. 0 | Page 17 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ADD5205ACPZ-RL | IC LED DVR WHITE BCKLGT 12LFCSP |
| ADE5566ASTZF62-RL | IC ENERGY METERING 1PHASE 64LQFP |
| ADE7156ASTZF16 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7518ASTZF8-RL | IC ENERGY METER MCU 8K 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADD5205 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Four-String White LED Driver |
| ADD5205ACPZ-RL | 功能描述:IC LED DVR WHITE BCKLGT 12LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ADD5207 | 制造商:AD 制造商全称:Analog Devices 功能描述:Four-String, White LED Driver |
| ADD52070001CPZR | 功能描述:IC LED DRIVER REGULATOR DIM 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADD5207ACPZ | 制造商:Analog Devices 功能描述:DRIVER LED 1MHZ 36V 14LFCSP 制造商:Analog Devices 功能描述:DRIVER, LED, 1MHZ, 36V, 14LFCSP 制造商:Analog Devices 功能描述:DRIVER, LED, 1MHZ, 36V, 14LFCSP, Topology:Boost (Step Up), No. of Outputs:1, Out 制造商:Analog Devices 功能描述:DRIVER, LED, 1MHZ, 36V, 14LFCSP, Topology:Boost (Step Up), No. of Outputs:1, Output Voltage:36V, Driver Case Style:LFCSP, Input Voltage Min:6V, Input Voltage Max:21V, Dimming Control Type:PWM, Switching Frequency:1MHz, Operating , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。