- 您现在的位置：买卖IC网 > PDF目录20620 > ADE7752AARZ-RL (Analog Devices Inc)IC ENERGY METERING 3PHASE 24SOIC PDF资料下载
参数资料
| 型号： | ADE7752AARZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PHASE 24SOIC |
| 标准包装： | 1,000 |
| 输入阻抗： | 450 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 6mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-ADE7752AEBZ-ND - BOARD EVALUATION FOR ADE7752A |
ADE7752/ADE7752A
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
CF
1
24
F1
DGND 2
V DD 3
23
22
F2
S1
REVP
4
21
S0
IAP 5
IAN 6
ADE7752/
ADE7752A
TOP VIEW
20
19
CLKOUT
CLKIN
IBP 7 (Not to Scale) 18 SCF
IBN 8
ICP 9
ICN 10
AGND 11
REF IN/OUT 12
17
16
15
14
13
ABS
VAP
VBP
VCP
VN
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5, 6;
7, 8;
9, 10
11
12
13–16
17
18
Mnemonic
CF
DGND
V DD
REVP
IAP, IAN;
IBP, IBN;
ICP, ICN
AGND
REF IN/OUT
VN, VCP, VBP,
VAP
ABS
SCF
Description
Calibration Frequency Logic Output. The CF logic output gives instantaneous real power information.
This output is intended to be used for calibration purposes. See the SCF pin description.
This provides the ground reference for the digital circuitry in the ADE7752: the multiplier, filters, and
digital-to-frequency converter. Because the digital return currents in the ADE7752 are small, it is
acceptable to connect this pin to the analog ground plane of the whole system.
Power Supply. This pin provides the supply voltage for the digital circuitry in the ADE7752. The supply
voltage should be maintained at 5 V ± 5% for specified operation. This pin should be decoupled to
DGND with a 10 μF capacitor in parallel with a 100 nF ceramic capacitor.
This logic output goes logic high when negative power is detected on any of the three phase inputs,
that is, when the phase angle between the voltage and the current signals is greater than 90°. This
output is not latched and is reset when positive power is once again detected. See the Negative Power
Information section.
Analog Inputs for Current Channel. This channel is intended for use with the current transducer and is
referenced in this document as the current channel. These inputs are fully differential voltage inputs
with maximum differential input signal levels of ±0.5 V. See the Analog Inputs section. Both inputs have
internal ESD protection circuitry. In addition, an overvoltage of ±6 V can be sustained on these inputs
without risk of permanent damage.
This pin provides the ground reference for the analog circuitry in the ADE7752: the ADCs, temperature
sensor, and reference. This pin should be tied to the analog ground plane or the quietest ground
reference in the system. This quiet ground reference should be used for all analog circuitry, such as
antialiasing filters, current and voltage transducers, and so on. To keep ground noise around the
ADE7752 to a minimum, the quiet ground plane should connect to the digital ground plane at only
one point. It is acceptable to place the entire device on the analog ground plane.
This pin provides access to the on-chip voltage reference. The on-chip reference has a nominal value of
2.4 V ± 8% and a typical temperature coefficient of 20 ppm/°C. An external reference source may also be
connected at this pin. In either case, this pin should be decoupled to AGND with a 1 μF ceramic capacitor.
Analog Inputs for the Voltage Channel. This channel is intended for use with the voltage transducer and
is referenced in this document as the voltage channel. These inputs are single-ended voltage inputs with
a maximum signal level of ±0.5 V with respect to VN for specified operation. All inputs have internal ESD
protection circuitry. In addition, an overvoltage of ± 6 V can be sustained on these inputs without risk of
permanent damage.
This logic input is used to select the way the three active energies from the three phases are summed.
This offers the designer the capability to do the arithmetical sum of the three energies (ABS logic high)
or the sum of the absolute values (ABS logic low). See the Mode Selection of the Sum of the Three Active
Energies section.
Select Calibration Frequency. This logic input is used to select the frequency on the calibration output
CF. Table 7 shows how the calibration frequencies are selected.
Rev. C | Page 6 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7566ASTZF16 | IC ENERGY METER 1PHASE 64-LQFP |
| GMM06DTBI | CONN EDGECARD 12POS R/A .156 SLD |
| RCB09DHNN | CONN EDGECARD 18POS DIP .050 SLD |
| ADE7762ARWZ-RL | IC ENERGY METERING 3PHASE 28SOIC |
| GMM06DTAI | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7752AR | 制造商:Rochester Electronics LLC 功能描述:THREE PHASE ACTIVE ENERGY METERING IC - Bulk 制造商:Analog Devices 功能描述:IC ENERGY METER |
| ADE7752ARRL | 制造商:Analog Devices 功能描述:Energy Measurement 24-Pin SOIC W T/R 制造商:Analog Devices 功能描述:IC ENERGY METER |
| ADE7752ARZ | 制造商:Analog Devices 功能描述:Energy Measurement 24-Pin SOIC W |
| ADE7752ARZ-RL | 制造商:Analog Devices 功能描述:Energy Measurement 24-Pin SOIC W T/R |
| ADE7752B | 制造商:AD 制造商全称:Analog Devices 功能描述:Polyphase Energy Metering IC with Pulsed Output |
发布紧急采购，3分钟左右您将得到回复。