- 您现在的位置：买卖IC网 > PDF目录20620 > ADE7754ARZRL (Analog Devices Inc)IC ENERGY METERING 3PHASE 24SOIC PDF资料下载
参数资料
| 型号： | ADE7754ARZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/44页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PHASE 24SOIC |
| 标准包装： | 1 |
| 输入阻抗： | 370 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 7mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 剪切带 (CT) |
| 配用： | EVAL-ADE7754EBZ-ND - BOARD EVALAUTION FOR ADE7754 |
| 其它名称： | ADE7754ARZRLCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
ADE7754
VPEAK[7:0]
V AP , V BP , OR V CP
PKV RESET
0.07
0.06
0.05
0.04
LOW WHEN
RSTATUS
0.03
PKV INTERRUPT
FLAG (BIT C OF
STATUS REGISTER)
READ
RSTATUS
REGISTER
REGISTER
IS READ
0.02
0.01
0
–0.01
Figure 17. Peak Detection
0
100
200
300
400
500
600
700
800
900
1k
FREQUENCY (Hz)
Bits 2 and 3 of the measurement mode register define the phase
supporting the peak detection. Current and voltage of this phase
can be monitored at the same time. Figure 17 shows a line
voltage exceeding a threshold set in the voltage peak register
(VPEAK[7:0]). The voltage peak event is recorded by setting
the PKV flag in the interrupt status register. If the PKV enable
bit is set to Logic 1 in the interrupt enable register, the IRQ
logic output goes active low. See the Interrupts section.
Peak Level Set
The contents of the VPEAK and IPEAK registers compare to
the absolute value of the most significant byte output of the
selected voltage and current channels, respectively. Thus, for
example, the nominal maximum code from the current channel
ADC with a full-scale signal is 28F5C2h. See the Current
Channel Sampling section. Therefore, writing 28h to the
IPEAK register will put the current channel peak detection level
at full scale and set the current peak detection to its least sensi-
Figure 18a. Phase Response of the HPF and
Phase Compensation (10 Hz to 1 kHz)
0.010
0.008
0.006
0.004
0.002
0
–0.002
–0.004
tive value. Writing 00h puts the current channel detection level at
40
45
50
55
60
65
70
zero. The detection is done when the content of the IPEAK
register is smaller than the incoming current channel sample.
FREQUENCY (Hz)
Figure 18b. Phase Response of the HPF and
Phase Compensation (40 Hz to 70 Hz)
TEMPERATURE MEASUREMENT
The ADE7754 also includes an on-chip temperature sensor. A
temperature measurement is made every 4/CLKIN seconds.
The output from the temperature sensing circuit is connected
to an ADC for digitizing. The resulting code is processed and
placed into the temperature register (TEMP[7:0]) which can
be read by the user and has an address of 08h. See the Serial
Interface section. The contents of the temperature register are
signed (twos complement) with a resolution of 4 ° C/LSB. The
temperature register produces a code of 00h when the ambient
temperature is approximately 129 ° C. The value of the register is
temperature register = (temperature ( ° C) – 129)/4. The tempera-
ture in the ADE7754 has an offset tolerance of approximately
± 5 ° C. The error can be easily calibrated out by an MCU.
PHASE COMPENSATION
When the HPFs are disabled, the phase difference between the
current channel (IA, IB, and IC) and the voltage channel (VA,
VB, and VC) is zero from dc to 3.3 kHz. When the HPFs are
enabled, the current channels have a phase response as shown in
Figure 18a and 18b. The magnitude response of the filter is
shown in Figure 18c. As seen from in the plots, the phase response
is almost zero from 45 Hz to 1 kHz. This is all that is required
in typical energy measurement applications.
0.010
0.008
0.006
0.004
0.002
0
–0.002
–0.004
44 46 48 50 52 54 56
FREQUENCY (Hz)
Figure 18c. Gain Response of HPF and Phase Com-
pensation (Deviation of Gain as % of Gain at 54 Hz)
Despite being internally phase compensated, the ADE7754 must
work with transducers that may have inherent phase errors. For
example, a phase error of 0.1 ° to 0.3 ° is not uncommon for a CT
(current transformer). These phase errors can vary from part to
part, and they must be corrected in order to perform accurate
power calculations. The errors associated with phase mismatch
–14 –
REV. 0
相关PDF资料 |
PDF描述 |
|---|---|
| R1S12-3.315/P | CONV DC/DC 1W 3.3VIN 15VOUT |
| EEM25DTMN-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| V48C48H75BF2 | CONVERTER MOD DC/DC 48V 75W |
| EYM12DTMD-S189 | CONN EDGECARD 24POS R/A .156 SLD |
| V48C48H75BF | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7755 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output |
| ADE7755AARSRL | 制造商:Analog Devices 功能描述:ENERGY METERING IC WITH P - Tape and Reel |
| ADE7755AN | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADE7755AN-REF | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output |
| ADE7755ARS | 制造商:Analog Devices 功能描述:Energy Measurement 24-Pin SSOP 制造商:Rochester Electronics LLC 功能描述:ENERGY METERING IC WITH PULSE OUTPUT - Bulk 制造商:Analog Devices 功能描述:IC ENERGY METER 制造商:Maxim Integrated Products 功能描述:POWER METERING, 24 Pin, Plastic, SSOP |
发布紧急采购，3分钟左右您将得到回复。