- 您现在的位置：买卖IC网 > PDF目录1898 > ADM1024ARUZ-R7 (ON Semiconductor)IC MONITOR SYS TEMP/VOLT 24TSSOP PDF资料下载
参数资料
| 型号： | ADM1024ARUZ-R7 |
| 厂商： | ON Semiconductor |
| 文件页数： | 20/30页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SYS TEMP/VOLT 24TSSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation 30/Sept/2011 |
| 标准包装： | 1,000 |
| 应用： | PC，PDA |
| 接口： | 串行 |
| 电源电压： | 2.8 V ~ 5.5 V |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
ADM1024
http://onsemi.com
27
Table 13. REGISTER 40H, CONFIGURATION REGISTER 1 (POWER-ON DEFAULT, 08H)
Bit
Name
R/W
Description
0
START
R/W
Logic 1 enables startup of ADM1024; Logic 0 places it in standby mode. Caution:
The outputs of the interrupt pins will not be cleared if the user writes a 0 to this
location after an interrupt has occurred (see “INT Clear” bit). At startup, limit
checking functions and scanning begins. Note, all high and low limits should be set
into the ADM1024 prior to turning on this bit (PowerOn Default = 0).
1
INT_Enable
R/W
Logic 1 enables the INT_output. 1 = Enabled 0 = Disabled (PowerOn Default = 0).
2
THERM
Enable
R/W
0 = THERM disabled
1 = THERM enabled
3
INT_Clear
R/W
During Interrupt Service Routine (ISR), this bit is asserted Logic 1 to clear INT output
without affecting the contents of the Interrupt Status Register. The device will stop
monitoring. It will resume upon clearing of this bit. (PowerOn Default = 0)
4
RESET
R/W
Setting this bit generates a low going 45 ms reset pulse at Pin 12. This bit is
selfclearing and poweron default is 0.
5
Reserved
R/W
Default = 0
6
THERM CLR
R/W
A 1 clears the THERM output without changing the Status Register contents.
7
Initialization
R/W
Logic 1 restores poweron default values to the Configuration Register, Interrupt
Status Registers, Interrupt Mask Registers, Fan Divisor Register, and the
Temperature Configuration Register. This bit automatically clears itself since the
poweron default is 0.
Table 14. REGISTER 41H, INTERRUPT STATUS REGISTER 1 (POWER-ON DEFAULT, 00H)
Bit
Name
R/W
Description
0
2.5 V/External Temp2
Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
1
VCCP1 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
2
VCC Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
3
5.0 V Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
4
Internal Temp Error
Read only
A 1 indicates that a temperature interrupt has been set, or that a High or Low limit
has been exceeded.
5
External Temp1 Error
Read only
A 1 indicates that a temperature interrupt has been set, or that a High or Low limit
has been exceeded.
6
FAN1/AIN1 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
7
FAN2/AIN2 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
Bit
Name
R/W
Description
0
12 V Error
Read only
A 1 indicates a High or Low limit has been exceeded.
1
VCCP2 Error
Read only
A 1 indicates a High or Low limit has been exceeded.
2
Reserved
Read only
Undefined.
3
Reserved
Read only
Undefined.
4
Chassis Error
Read only
A 1 indicates Chassis Intrusion has gone high.
5
THERM Interrupt
Read only
Indicates that THERM pin has been pulled low by an external source.
6
D1 Fault
Read only
Short or OpenCircuit Sensor Diode D1.
7
D2 Fault
Read only
Short or OpenCircuit Sensor Diode D2.
1. Any time the Status Register is read out, the conditions (i.e., Register) that are read are automatically reset. In the case of the channel priority
indication, if two or more channels were out of limits, then another indication would automatically be generated if it was not handled during
the ISR.
2. In the Mask Register, the errant voltage interrupt may be disabled until the operator has time to clear the errant condition or set the limit
higher/lower.
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1025ARQZ-R7 | IC MONITOR SYS/VOLT 5CH 16QSOP |
| ADM1181AAN | IC TXRX RS-232 5V 15KV 16DIP |
| ADM1385ARS | IC TXRX RS-232 HI-SP 3.3V 20SSOP |
| ADM1485ARMZ-REEL7 | IC TXRX RS-485 5V HS 8MSOP |
| ADM1486AR | IC TX/RX RS-485 PRO-BUS 5V 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1024ARUZ-REEL | 功能描述:板上安装温度传感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
| ADM1024EVB | 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1025 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025A | 制造商:AD 制造商全称:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
发布紧急采购，3分钟左右您将得到回复。