- 您现在的位置：买卖IC网 > PDF目录373995 > ADM1026 (Analog Devices, Inc.) Complete Thermal and System Management Controller PDF资料下载
参数资料
| 型号： | ADM1026 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | Complete Thermal and System Management Controller |
| 中文描述： | 完整的热和系统管理控制器 |
| 文件页数： | 31/56页 |
| 文件大小： | 634K |
| 代理商： | ADM1026 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADM1026
Note that the THERM pin is bidirectional, so THERM may be
pulled low externally as an input. This causes the PWM and
DAC outputs to go to full scale until THERM is returned high
again. To disable THERM as an input, set Bit 0 of Configuration
Register 3 (Reg. 07h). This configures Pin 42 as GPIO16 and
prevents a low on Pin 42 from driving the fans at full speed.
Rev. A | Page 31 of 56
THERM LIMIT
THERM LIMIT – 5°C
THERM
INT
INT CLEARED BY STATUS REG 1 READ,
BIT 2 OF CONFIG. REG. 1 SET, OR ARA
TEMPERATURE
0
Figure 54. Assertion of INT Due to THERM Event
Reset Input and Outputs
The ADM1026 has two active low, power-on reset outputs,
RESETMAIN and RESETSTBY. These operate as follows.
RESETSTBY monitors 3.3 V STBY. At power-up, RESETSTBY is
asserted (pulled low) until 180 ms after 3.3 V STBY rises above
the reset threshold.
RESETMAIN monitors 3.3 V MAIN. This means that at power-
up, RESETMAIN is asserted (pulled low) until 180 ms after
3.3 V MAIN rises above the reset threshold.
If 3.3 V MAIN rises with or before DV
CC
, RESETMAIN
remains asserted until 180 ms after RESETSTBY is negated.
RESETMAIN can also function as a RESET input. Pulling this
pin low resets the registers, which are initialized to their default
values by a software reset. (See the Software Reset Function
section for register details).
Note that the 3.3 V STBY pin supplies power to the ADM1026.
In applications that do not require monitoring of a 3.3 V STBY
and 3.3 V MAIN supply, these two pins should be connected
together (3.3 V MAIN should not be left floating).
To ensure that the 3.3 V STBY pin does not become backdriven,
the 3.3 V STBY supply should power on before all other voltages
in the system.
See Table 3 for more information about pin configuration.
RESETSTBY
RESETMAIN
3.3VMAIN
~1V
180ms
POWER-ON RESET
180ms
3.3VSTBY
~1V
0
Figure 55. Operation of Offset Outputs
NAND TREE TESTS
A NAND tree is provided in the ADM1026 for automated test
equipment (ATE) board-level connectivity testing. This allows
the functionality of all digital inputs to be tested in a simple
manner and any pins that are nonfunctional or shorted together
to be identified. The structure of the NAND tree is shown in
Figure 56. The device is placed into NAND tree test mode by
powering up with Pin 25 held high. This pin is sampled
automatically after power-up, and if it is connected high, then
the NAND test mode is invoked.
NTESTOUT
GPIO8
FAN0
FAN1
FAN2
FAN3
FAN4
FAN5
FAN6
CI
SDA
SCL
FAN7
INT
GPIO9
GPIO10
GPIO11
GPIO12
GPIO13
GPIO14
GPIO15
GPIO16
0
Figure 56. NAND Tree
The NAND tree test may be carried out in one of two ways.
1.
Start with all inputs low and take them high in turn,
starting with the input nearest to NTEST_OUT
(GPIO16/THERM) and working back up the tree to the
input furthest from NTESTOUT (INT). This should give
the characteristic output pattern shown in Figure 57, with
NTESTOUT toggling each time an input is taken high.
2.
Start with all inputs high and take them low in turn,
starting with the input furthest from NTEST_OUT (INT)
and working down the tree to the input nearest to
NTEST_OUT (GPIO16/ THERM). This should give a
similar output pattern to Figure 58.
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1026JST-REEL | Complete Thermal and System Management Controller |
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
| ADM1026JST | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1026EBZEVB | 功能描述:BOARD EVAL FOR ADM1026 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1026JST | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解决方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。