- 您现在的位置：买卖IC网 > PDF目录22035 > ADM1026JST (ON Semiconductor)IC CNTRL SYS REF/EEPROM 48LQFP PDF资料下载
参数资料
| 型号： | ADM1026JST |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/55页 |
| 文件大小： | 0K |
| 描述： | IC CNTRL SYS REF/EEPROM 48LQFP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Obsolescence 30/Sept/2009 |
| 标准包装： | 250 |
| 功能： | 硬件监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 100°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
ADM1026
Functional Description
The ADM1026 is a complete system hardware monitor for
microprocessor-based systems. The device communicates
with the system via a serial system management bus. The
serial bus controller has a hardwired address line for device
selection (ADD, Pin 15), a serial data line for reading and
writing addresses and data (SDA, Pin 14), and an input line
for the serial clock (SCL, Pin 13). All control and
programming functions of the ADM1026 are performed over
the serial bus.
Measurement Inputs
Programmability of the analog and digital measurement
inputs makes the ADM1026 extremely flexible and
versatile. The device has an 8-bit A/D converter, and 17
analog measurement input pins that can be configured in
different ways.
Pins 25 and 26 are dedicated temperature inputs and may
be connected to the cathode and anode of a remote
temperature sensing diode.
Pins 27 and 28 may be configured as temperature inputs
and connected to a second temperature-sensing diode, or may
be reconfigured as analog inputs with a range of 0 V to 2.5 V.
Pins 29 to 33 are dedicated analog inputs with on-chip
attenuators configured to monitor V BAT , +5.0 V, ? 12 V,
+12 V, and the processor core voltage V CCP , respectively.
Pins 34 to 41 are general-purpose analog inputs with a
range of 0 V to 2.5 V or 0 V to 3.0 V. These are mainly
intended for monitoring SCSI termination voltages, but may
Chassis Intrusion
A chassis intrusion input (Pin 16) is provided to detect
unauthorized tampering with the equipment. This event is
latched in a battery-backed register bit.
Resets
The ADM1026 has two power-on reset outputs,
RESETMAIN and RESETSTBY, that are asserted when
3.3 V MAIN or 3.3 V STBY fall below the r eset threshold.
These give a 180 ms reset pulse at powerup. RESETMAIN
also functions as an active-low RESET input.
Fan Speed Control Outputs
The ADM1026 has two outputs intended to control fan
speed, though they can also be used for other purposes.
Pin 18 is an open drain, Pulse Width Modulated (PWM)
output with a programmable duty cycle and an output
frequency of 75 Hz. Pin 23 is connected to the output of an
on-chip, 8-bit, digital-to-analog converter with an output
range of 0 V to 2.5 V.
Either or both of these outputs may be used to implement
a temperature-controlled fan by controlling the speed of a
fan using the temperature measured by the on-chip
temperature sensor or remote temperature sensors.
Internal Registers
Table 5 describes the principal registers of the ADM1026.
For more detailed information, see Table 12 to Table 125.
Table 5. PRINCIPLE REGISTERS
be used for other purposes.
The ADC also accepts input from an on-chip band gap
temperature sensor that monitors system ambient
temperature.
In addition, the ADM1026 monitors the supply from
which it is powered, 3.3 V STBY, so there is no need for a
separate pin to monitor the power supply voltage.
The ADM1026 has eight pins that are general-purpose
logic I/O pins (Pins 1, 2, and 43 to 48), a pin that can be
configured as GPIO or as a bidirectional thermal interrupt
(THERM) pin (Pin 42), and eight pins that can be configured
for fan speed measurement or as general-purpose logic pins
(Pins 3 to 6 and Pins 9 to 12).
Sequential Measurement
When the ADM1026 monitoring sequence is started, it
cycles sequentially through the measurement of analog
inputs and the temperature sensor, while at the same time the
fan speed inputs are independently monitored. Measured
values from these inputs are stored in value registers. These
can be read over the serial bus, or can be compared with
programmed limits stored in the limit registers. The results
Type
Address
Pointer
Configuration
Registers
Fan Divisor
Registers
DAC/PWM
Control
Registers
GPIO
Configuration
Registers
Value and
Limit
Registers
Status
Registers
Mask
Registers
Description
Contains the address that selects one of
the other internal registers. When writing to
the ADM1026, the first byte of data is
always a register address, and is written to
the address pointer register.
Provide control and configuration for
various operating parameters.
Contain counter prescaler values for fan
speed measurement.
Contain speed values for PWM and DAC
fan drive outputs.
Configure the GPIO pins as input or output
and for signal polarity.
Store the results of analog voltage inputs,
temperature, and fan speed measurements,
along with their limit values.
Store events from the various interrupt
sources.
Allow masking of individual interrupt
sources.
of out-of-limit comparisons are stored in the interrupt status
registers. An out-of-limit event generates an interrupt on the
INT line (Pin 17).
Any or all of the interrupt status bits can be masked by
appropriate programming of the interrupt mask registers.
EEPROM
The ADM1026 has 8 kB of non-volatile, electrically
erasable, programmable read-only memory (EEPROM)
from register Addresses 8000h to 9FFFh. This may be used
for permanent storage of data that is not lost when the
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| LQG15HSR22J02D | INDUCTOR 220NH 120MA 0402 |
| GCC10DCSN | CONN EDGECARD 20POS DIP .100 SLD |
| VJ1206Y122KBAAT4X | CAP CER 1200PF 50V 10% X7R 1206 |
| VI-B3X-CX | CONVERTER MOD DC/DC 5.2V 75W |
| VJ1206Y122KBBAT4X | CAP CER 1200PF 100V 10% X7R 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解决方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| ADM1026JSTZ-R7 | 功能描述:PMIC 解决方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| ADM1026JSTZ-REEL | 功能描述:板上安装温度传感器 HI INT SYS MONITR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。