- 您现在的位置：买卖IC网 > PDF目录22039 > ADM1027ARQ-REEL (ON Semiconductor)IC REMOTE THERMAL CTRLR 24-QSOP PDF资料下载
参数资料
| 型号： | ADM1027ARQ-REEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 18/56页 |
| 文件大小： | 1822K |
| 描述： | IC REMOTE THERMAL CTRLR 24-QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation Notice 25/Aug/2008 |
| 标准包装： | 2,500 |
| 系列： | dBCool® |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 105°C，外部传感器 |
| 精确度： | ±1°C |
| 拓扑： | ADC，比较器，风扇速度计数器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
REV. A
18
ADM1027
ANALOG MONITORING CYCLE TIME
The analog monitoring cycle begins when a 1 is written to the
start bit (Bit 0) of Configuration Register 1(Reg. 0x40). The
ADC measures each analog input in turn and as each mea-
surement is completed, the result is automatically stored in the
appropriate value register. This round-robin monitoring cycle
continues unless disabled by writing a 0 to Bit 0 of Configura-
tion Register 1.
Since the ADC will normally be left to free-run in this manner,
the time taken to monitor all the analog inputs will normally not
be of interest as the most recently measured value of any input
can be read out at any time.
For applications where the monitoring cycle time is important,
it can easily be calculated.
The total number of channels measured is
y Four dedicated supply voltage inputs
y 3.3 V
STBY
or 5 V supply (V
CC
pin)
y Local temperature
y Two remote temperatures
As mentioned previously, the ADC performs round-robin con-
versions and takes 11.38 ms for each voltage measurement,
12 ms for a local temperature reading, and 25.5 ms for a remote
temperature reading.
The total monitoring cycle time for averaged voltage and tem-
perature monitoring is therefore nominally
(5 11.38) + 12 + (2 25.5) = 120 ms
Fan TACH measurements are made in parallel and are not
synchronized with the analog measurements in any way.
STATUS REGISTERS
The results of limit comparisons are stored in Status Registers 1
and 2. The status register bit for each channel reflects the status of
the last measurement and limit comparison on that channel.
If a measurement is within limits, the corresponding status
register bit will be cleared to 0. If the measurement is out-of-limits,
the corresponding status register bit will be set to 1.
The state of the various measurement channels may be polled by
reading the status registers over the serial bus. When 1, Bit 7
(OOL) of Status Register 1 (Reg. 0x41) means that an out-of-
limit event has been flagged in Status Register 2. This means that
the user need read only Status Register 2 when this bit is set.
Alternatively, Pin 10 can be configured as an SMBALERT output.
This will automatically notify the system supervisor of an
out-of-limit condition. Reading the status registers clears the
appropriate status bit as long as the error condition that caused
the interrupt has cleared. Status register bits are sticky.
Whenever a status bit gets set, indicating an out-of-limit
condition, it will remain set even if the event that caused it has
gone away (until read). The only way to clear the status bit is to
read the status register after the event has gone away. Interrupt
status mask registers (Reg. 0x74, 0x75) allow individual inter-
rupt sources to be masked from causing an SMBALERT.
However, if one of these masked interrupt sources goes out-
of-limit, its associated status bit will get set in the interrupt
status registers.
STATUS REGISTER 1 (REG. 0x41)
Bit 7 (OOL) = 1, denotes a bit in Status Register 2 is set and
Status Register 2 should be read.
Bit 6 (R2T) = 1, Remote 2 temp high or low limit has been
exceeded.
Bit 5 (LT) = 1, Local temp high or low limit has been exceeded.
Bit 4 (R1T) = 1, Remote 1 temp high or low limit has been
exceeded.
Bit 3 (5 V) = 1, 5 V high or low limit has been exceeded.
Bit 2 (V
CC
) = 1, V
CC
high or low limit has been exceeded.
Bit 1 (V
CCP
) = 1, V
CCP
high or low limit has been exceeded.
Bit 0 (2.5 V) = 1, 2.5 V high or low limit has been exceeded.
STATUS REGISTER 2 (REG. 0x42)
Bit 7 (D2) = 1, indicates an open or short on D2+/D2 inputs.
Bit 6 (D1) = 1, indicates an open or short on D2+/D2 inputs.
Bit 5 (FAN4) = 1, indicates Fan 4 has dropped below mini-
mum speed.
Bit 4 (FAN3) = 1, indicates Fan 3 has dropped below mini-
mum speed.
Bit 3 (FAN2) = 1, indicates Fan 2 has dropped below mini-
mum speed.
Bit 2 (FAN1) = 1, indicates Fan 1 has dropped below mini-
mum speed.
Bit 1 (OVT) = 1, indicates that a THERM overtemperature
limit has been exceeded.
Bit 0 (12 V) = 1, 12 V high or low limit has been exceeded.
Rev. 3 | Page 18 of 56 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| AGL030V2-QNG68 | IC FPGA IGLOO 1.2-1.5V 68QFN |
| AGL030V5-VQG100 | IC FPGA IGLOO 1.5V 100VQFP |
| AMC22DRTS-S93 | CONN EDGECARD 44POS DIP .100 SLD |
| F931C226KCC | CAP TANT 22UF 16V 10% 2312 |
| ADM1031ARQ-REEL | IC SENSOR 2-TEMP/FAN CTRL 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1027ARQ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1027ARQSMSC | 功能描述:IC SENSOR TEMP/FAN CTRL 制造商:analog devices inc. 系列:* 零件状态:上次购买时间 标准包装:1 |
| ADM1027ARQZ | 功能描述:板上安装温度传感器 VOLT THRM MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1027ARQZ-REEL | 功能描述:板上安装温度传感器 VOLT THRM MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADM1027ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 24QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。