- 您现在的位置：买卖IC网 > Datasheet目录39 > ADM1027ARQZ-RL7 (ON Semiconductor)IC REMOTE THERMAL CTLR 24QSOP Datasheet资料下载
参数资料
| 型号： | ADM1027ARQZ-RL7 |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/56页 |
| 文件大小： | 1822K |
| 描述： | IC REMOTE THERMAL CTLR 24QSOP |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation Notice 25/Aug/2008 Product Obsolescence 30/Sept/2009 |
| 标准包装： | 1,000 |
| 系列： | dBCool® |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | 0°C ~ 105°C，外部传感器 |
| 精确度： | ±1°C |
| 拓扑： | ADC，比较器，风扇速度计数器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
REV. A
ADM1027
23
FAN SPEED MEASUREMENTS
TACH Inputs
Pins 11, 12, 9, and 14 are open-drain TACH inputs intended
for fan speed measurement.
Signal conditioning in the ADM1027 accommodates the slow
rise and fall times typical of fan tachometer outputs. The maxi-
mum input signal range is 0 V to 5 V, even where V
CC
is less
than 5 V. In the event that these inputs are supplied from fan
outputs that exceed 0 V to 5 V, either resistive attenuation of
the fan signal or diode clamping must be included to keep
inputs within an acceptable range.
Figures 25a to 25d show circuits for most common fan TACH
outputs. If the fan TACH output has a resistive pull-up to V
CC
, it
can be connected directly to the fan input, as shown in Figure 25a.
5V OR 12V
ADM1027
FAN SPEED
COUNTER
TACH X
TACHO
OUTPUT
PULL-UP
4.7k
TYP
V
CC
FAN
Figure 25a. Fan With TACH Pull-Up to +V
CC
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 5 V), then the fan output can be clamped with a
Zener diode, as shown in Figure 25b. The Zener diode voltage
should be chosen so that it is greater than V
IH
of the TACH
input but less than 5 V, allowing for the voltage tolerance of the
Zener. A value of between 3 V and 5 V is suitable.
5V OR 12V
ADM1027
FAN SPEED
COUNTER
TACH X
TACHO
OUTPUT
PULL-UP
4.7k
TYP
V
CC
FAN
ZD1*
*CHOOSE ZD1 VOLTAGE APPROX 0.8 V
CC
Figure 25b. Fan with TACH Pull-Up to Voltage
> 5 V (e.g., 12 V) Clamped with Zener Diode
If the fan has a strong pull-up (less than 1 k) to 12 V, or a
totem-pole output, then a series resistor can be added to limit
the Zener current, as shown in Figure 25c. Alternatively, a
resistive attenuator may be used, as shown in Figure 25d.
R1 and R2 should be chosen such that
2
2
1
2 5
V V
R R
R
R
V
PULLUP
PULLUP
<
?/DIV>
+
+
(
)
>
The fan inputs have an input resistance of nominally 160 kW to
ground; this should be taken into account when calculating
resistor values.
With a pull-up voltage of 12 V and pull-up resistor less than
1 kW, suitable values for R1 and R2 would be 100 kW and
47 kW. This will give a high input voltage of 3.83 V.
5V OR 12V
ADM1027
FAN SPEED
COUNTER
TACH X
TACHO
OUTPUT
PULL-UP TYP
<1k
OR
TOTEM POLE
V
CC
FAN
ZD1*
*CHOOSE ZD1 VOLTAGE APPROX 0.8 V
CC
R1
10k
Figure 25c. Fan with Strong TACH Pull-Up to > V
CC
or
Totem-Pole Output, Clamped with Zener and Resistor
5V OR 12V
ADM1027
FAN SPEED
COUNTER
TACH X
TACHO
OUTPUT
PULL-UP TYP
<1k
V
CC
FAN
R2*
*SEE TEXT
R1*
Figure 25d. Fan with Strong TACH Pull-Up to > V
CC
or Totem-Pole Output, Attenuated with R1/R2
Fan Speed Measurement
The fan counter does not count the fan TACH output pulses
directly because the fan speed may be less than 1000 RPM and
it would take several seconds to accumulate a reasonably large
and accurate count. Instead, the period of the fan revolution is
measured by gating an on-chip 90 kHz oscillator into the input
of a 16-bit counter for N periods of the fan TACHO output
(Figure 26), so the accumulated count is actually proportional
to the fan tachometer period and inversely proportional to the
fan speed.
1
2
3
4
LOCK
PWM
TACH
Figure 26. Fan Speed Measurement
N, the number of pulses counted, is determined by the settings
of Register 0x7B (fan pulses per revolution register). This register
contains two bits for each fan, allowing 1, 2 (default), 3, or 4
TACH pulses to be counted.
Rev. 3 | Page 23 of 56 | www.onsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| ADM1029ARQZ-R7 | IC SENSOR 2TEMP/FAN CTRL 24QSOP |
| ADM1030ARQZ-RL7 | IC SNSR TEMP/FAN PWM CTRL 16QSOP |
| ADM1032ARZ-REEL | IC TEMP MONITOR 85DEG 8SOIC |
| ADM1033ARQZ-RL7 | IC THERM/FAN SPEED CTLR 16-QSOP |
| ADM1034ARQZ-REEL | IC THERM/FAN SPEED CTRLR 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1027ARQZ-RL71 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:dBCOOLa?￠ Remote Thermal Controller and Voltage Monitor |
| ADM1028 | 制造商:AD 制造商全称:Analog Devices 功能描述:Remote Thermal Diode Monitor with Linear Fan Control |
| ADM1028ARQ | 功能描述:IC SENSOR TEMP/FAN CTRL 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADM1028ARQ-REEL7 | 制造商:Rochester Electronics LLC 功能描述:TDM + LINEAR FAN CONTROL I.C. - Tape and Reel |
| ADM1029 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual PWM Fan Controller and Temperature Monitor for High Availability Systems |
发布紧急采购，3分钟左右您将得到回复。