- 您现在的位置：买卖IC网 > PDF目录15309 > ADM1065ACPZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 40-LFCSP PDF资料下载
参数资料
| 型号： | ADM1065ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40-LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 10 |
| 输出： | 可编程 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 托盘 |
| 配用： | EVAL-ADM1065TQEBZ-ND - BOARD EVALUATION FOR ADM1065TQ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADM1065
The hysteresis value is given by
V HYST = V R × N THRESH /255
where:
V HYST is the desired hysteresis voltage.
N THRESH is the decimal value of the 5-bit hysteresis code.
Note that N THRESH has a maximum value of 31. The maximum
INPUT GLITCH FILTERING
The final stage of the SFDs is a glitch filter. This block provides
time-domain filtering on the output of the SFD comparators,
which allows the user to remove any spurious transitions such
as supply bounce at turn-on. The glitch filter function is in addition
to the digitally programmable hysteresis of the SFD comparators.
The glitch filter timeout is programmable up to 100 μs.
For example, when the glitch filter timeout is 100 μs, any pulse
appearing on the input of the glitch filter block that is less than
100 μs in duration is prevented from appearing on the output of
the glitch filter block. Any input pulse that is longer than 100 μs
appears on the output of the glitch filter block. The output is
delayed with respect to the input by 100 μs. The filtering process
An additional supply supervision function is available when the
VXx pins are selected as digital inputs. In this case, the analog
function is available as a second detector on each of the dedi-
cated analog inputs, VPx and VH. The analog function of VX1
is mapped to VP1, VX2 is mapped to VP2, and so on. VX5 is
mapped to VH. In this case, these SFDs can be viewed as secondary
or warning SFDs.
The secondary SFDs are fixed to the same input range as the
primary SFDs. They are used to indicate warning levels rather
than failure levels. This allows faults and warnings to be generated
on a single-supply using only one pin. For example, if VP1 is set
to output a fault when a 3.3 V supply drops to 3.0 V, VX1 can be
set to output a warning at 3.1 V. Warning outputs are available for
readback from the status registers. They are also OR’ed together and
fed into the SE, allowing warnings to generate interrupts on the
PDOs. Therefore, in this example, if the supply drops to 3.1 V,
a warning is generated, and remedial action can be taken before
the supply drops out of tolerance.
VXx PINS AS DIGITAL INPUTS
As discussed in the Supply Supervision with VXX Inputs section,
the VXx input pins on the ADM1065 have dual functionality.
The second function is as a digital logic input to the device.
INPUT PULSE SHORTER
THAN GLITCH FILTER TIMEOUT
PROGRAMMED
TIMEOUT
INPUT
INPUT PULSE LONGER
THAN GLITCH FILTER TIMEOUT
PROGRAMMED
TIMEOUT
INPUT
Therefore, the ADM1065 can be configured for up to five digital
inputs. These inputs are TTL-/CMOS-compatible. Standard logic
signals can be applied to the pins, RESET from reset generators,
PWRGD signals, fault flags, manual resets, and more. These signals
are available as inputs to the SE and, therefore, can be used to
control the status of the PDOs. The inputs can be configured to
detect either a change in level or an edge.
t 0
t GF
t 0
t GF
When configured for level detection, the output of the digital
block is a buffered version of the input. When configured for edge
detection, a pulse of programmable width is output from the
digital block, once the logic transition is detected. The width is
programmable from 0 μs to 100 μs.
OUTPUT
OUTPUT
The digital blocks feature the same glitch filter function that is
available on the SFDs. This function enables the user to ignore
t 0
t GF
t 0
t GF
spurious transitions on the inputs. For example, the filter can be
Figure 17. Input Glitch Filter Function
SUPPLY SUPERVISION WITH VXx INPUTS
The VXx inputs have two functions. They can be used as either
supply fault detectors or digital logic inputs. When selected as
analog (SFD) inputs, the VXx pins have functionality that is
used to debounce a manual reset switch.
When configured as digital inputs, each VXx pin has a weak
(10 μA) pull-down current source available for placing the input
into a known condition, even if left floating. The current source,
if selected, weakly pulls the input to GND.
very similar to the VH and VPx pins. The primary difference is
that the VXx pins have only one input range: 0.573 V to 1.375 V.
Therefore, these inputs can directly supervise only the very
VXx
(DIGITAL INPUT)
+
DETECTOR
GLITCH
FILTER
TO
SEQUENCING
ENGINE
low supplies. However, the input impedance of the VXx pins
is high, allowing an external resistor divide network to be
connected to the pin. Thus, potentially any supply can be
divided down into the input range of the VXx pin and
supervised. This enables the ADM1065 to monitor other
supplies, such as +24 V, +48 V, and ?5 V.
Rev. D | Page 13 of 28
–
VREF = 1.4V
Figure 18. VXx Digital Input Function
相关PDF资料 |
PDF描述 |
|---|---|
| EEC49DRTN-S93 | CONN EDGECARD 98POS DIP .100 SLD |
| VI-2WK-EW-F1 | CONVERTER MOD DC/DC 40V 100W |
| VI-2WJ-EW-F4 | CONVERTER MOD DC/DC 36V 100W |
| VI-2WJ-EW-F3 | CONVERTER MOD DC/DC 36V 100W |
| IMC1210BN27NJ | INDUCTOR WW 27NH 5% 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1065ASU | 制造商:AD 制造商全称:Analog Devices 功能描述:Super Sequencer-TM and Monitor |
| ADM1065ASU-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:Super Sequencer-TM and Monitor |
| ADM1065ASU-REEL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:Super Sequencer-TM and Monitor |
| ADM1065ASUZ | 功能描述:IC SEQUENCER/MONITOR 48-TQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM1065ASUZ-RL7 | 功能描述:IC SEQUENCER/MONITOR 48-TQFP 制造商:analog devices inc. 系列:Super Sequencer? 包装:剪切带（CT） 零件状态:在售 类型:序列发生器 受监控电压数:10 输出:可编程 复位:- 复位超时:- 电压 - 阈值:可调节/可选择 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:48-TQFP 供应商器件封装:48-TQFP（7x7） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。