- 您现在的位置：买卖IC网 > PDF目录16740 > ADM1168ASTZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 32LQFP PDF资料下载
参数资料
| 型号： | ADM1168ASTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 32LQFP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 应用： | 电源监控器，序列发生器 |
| 输入电压： | 3 V ~ 14.4 V |
| 电源电压： | 3 V ~ 14.4 V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
Monitoring Fault Detector
The monitoring fault detector block is used to detect a failure on an
input. The logical function implementing this is a wide OR gate
that can detect when an input deviates from its expected condition.
The clearest demonstration of the use of this block is in the
PWRGD state, where the monitor block indicates that a failure
on one or more of the VPx, VXx, or VH inputs has occurred.
No programmable delay is available in this block because the
triggering of a fault condition is likely to be caused by a supply
falling out of tolerance. In this situation, the device needs to react as
quickly as possible. Some latency occurs when moving out of this
state, however, because it takes a finite amount of time (~20 μs) for
the state configuration to download from the EEPROM into the
SE. Figure 22 is a block diagram of the monitoring fault detector.
MONITORING FAULT
DETECTOR
1-BIT FAULT
DETECTOR
ADM1168
FAULT AND STATUS REPORTING
The ADM1168 has a fault latch for recording faults. Two registers,
FSTAT1 and FSTAT2, are set aside for this purpose. A single bit
is assigned to each input of the device, and a fault on that input
sets the relevant bit. The contents of the fault register can be
read out over the SMBus to determine which input(s) faulted.
The fault register can be enabled or disabled in each state. To
latch data from one state, ensure that the fault latch is disabled
in the following state. This ensures that only real faults are
captured and not, for example, undervoltage conditions that
may be present during a power-up or power-down sequence.
The ADM1168 also has a number of status registers. These include
more detailed information, such as whether an undervoltage or
overvoltage fault is present on a particular input. The status
registers also include information on ADC limit faults.
There are two sets of these registers with different behaviors.
The first set of status registers is not latched in any way and,
VP1
SUPPLY FAULT
DETECTION
MASK
SENSE
FAULT
therefore, can change at any time in response to changes on the
inputs. These registers provide information such as the UV and
OV state of the inputs, the digital state of the GPI VXx inputs,
and the ADC warning limit status.
1-BIT FAULT
DETECTOR
The second set of registers update each time the sequence engine
changes state and are latched until the next state change. The
VX4
LOGIC INPUT CHANGE
OR FAULT DETECTION
MASK
SENSE
FAULT
second set of registers provides the same information as the first
set, but in a more compact form. The reason for this is that these
registers are used by the black box feature when writing status
information for the previous state into EEPROM.
1-BIT FAULT
DETECTOR
See the AN-721 Application Note for full details about the
WARNINGS
FAULT
ADM1168 registers.
NONVOLATILE BLACK BOX FAULT RECORDING
MASK
Figure 22. Monitoring Fault Detector Block Diagram
Timeout Detector
The timeout detector allows the user to trap a failure to ensure
proper progress through a power-up or power-down sequence.
In the sample application shown in Figure 21, the timeout next-
state transition is from the EN3V3 and EN2V5 states. For the
EN3V3 state, the signal 3V3ON is asserted on the PDO1 output
pin upon entry to this state to turn on a 3.3 V supply.
A section of EEPROM, from Address 0xF900 to Address 0xF9FF, is
provided that by default can be used to store user-defined settings
and information. Part of this section of EEPROM, Address 0xF980
to Address 0xF9FF, can instead be used to store up to 16 fault records.
Any sequencing engine state can be designated as a black box write
state. Each time the sequence engine enters that state, a fault record
is written into EEPROM. The fault record provides a snapshot of
the entire ADM1168 state at the point in time when the last state
was exited, just prior to entering the designated black box write
state. A fault record contains the following information:
This supply rail is connected to the VP2 pin, and the sequence
detector looks for the VP2 pin to go above its undervoltage
threshold, which is set in the supply fault detector (SFD) attached
to that pin.
The power-up sequence progresses when this change is detected. If,
however, the supply fails (perhaps due to a short circuit overloading
this supply), the timeout block traps the problem. In this example,
if the 3.3 V supply fails within 10 ms, the SE moves to the DIS3V3
state and turns off this supply by bringing PDO1 low. It also
indicates that a fault has occurred by taking PDO3 high. Timeout
?
?
?
?
?
?
?
A flag bit set to 0 after the fault record has been written.
The state number of the previous state prior to the fault
record write state.
Did a sequence, timeout, or monitor condition cause the
previous state to exit?
UVSTATx and OVSTATx input comparator status.
VXx GPISTAT status.
LIMSTATx status.
A checksum byte.
delays of 100 μs to 400 ms can be programmed.
Rev. A | Page 17 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| ES1000-NO.2-B9-X-COIL | HEAT SHRINK TUBING |
| 562A043-12-0 | BOOT MOLDED |
| VERSAFIT-3X-3/8-9-SP | HEAT SHRINK TUBING |
| 8S14-50FR | BOOT MOLDED |
| 0982661037 | CBL 33POS 0.5MM JMPR TYPE A 4" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1168ASTZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ACPZ | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ACPZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ BLACK BOX - Tape and Reel |
| ADM1169ASTZ | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。