参数资料
| 型号： | ADM3251EARWZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS232 ISOLATED 20-SOIC |
| 产品培训模块： | Power Line Monitoring iCoupler Digital Isolater Technology |
| 标准包装： | 37 |
| 类型： | 线路收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
| 配用： | EVAL-ADM3251EEB1Z-ND - BOARD EVALUATION FOR ADM3251 EVAL-ADM3251EEBZ-ND - BOARD EVALUATION ADM3251 |
Data Sheet
ADM3251E
THEORY OF OPERATION
The ADM3251E is a high speed, 2.5 kV fully isolated, single-
channel RS-232 transceiver device that operates from a single
power supply.
The internal circuitry consists of the following main sections:
Isolation of power and data
A charge pump voltage converter
A 5.0 V logic to EIA/TIA-232E transmitter
A EIA/TIA-232E to 5.0 V logic receiver
07388-
013
DECODE
RECT
REG
V–
C4
0.1F
16V
VOLTAGE
DOUBLER
C1+ C1– V+
VISO
C2+ C2–
R
T
VOLTAGE
INVERTER
VCC
ROUT
TIN
GND
GNDISO
RIN*
TOUT
ADM3251E
OSC
ENCODE
DECODE
*INTERNAL
5k PULL-DOWN RESISTOR ON THE RS-232 INPUT.
0.1F
C3
0.1F
10V
C2
0.1F
16V
0.1F
C1
0.1F
16V
Figure 13. Functional Block Diagram
ISOLATION OF POWER AND DATA
The ADM3251E incorporates a dc-to-dc converter section,
which works on principles that are common to most modern
power supply designs. VCC power is supplied to an oscillating
circuit that switches current into a chip-scale air core transformer.
Power is transferred to the secondary side, where it is rectified
to a high dc voltage. The power is then linearly regulated to
about 5.0 V and supplied to the secondary side data section and
to the VISO pin. The VISO pin should not be used to power
external circuitry.
Because the oscillator runs at a constant high frequency
independent of the load, excess power is internally dissipated
in the output voltage regulation process. Limited space for
transformer coils and components also adds to internal power
dissipation. This results in low power conversion efficiency.
The ADM3251E can be operated with the dc-to-dc converter
enabled or disabled. The internal dc-to-dc converter state of the
operating mode, VCC is set between 4.5 V and 5.5 V and the
internal dc-to-dc converter is enabled. To disable the dc-to-dc
converter, lower VCC to a value between 3.0 V and 3.7 V. In this
mode, the user must externally supply isolated power to the
VISO pin. An isolated secondary side voltage of between 3.0 V
and 5.5 V and a secondary side input current, IISO, of 12 mA
(maximum) is required on the VISO pin. The signal channels of
the ADM3251E then continue to operate normally.
The TIN pin accepts CMOS input levels (and TTL levels at
VCC = 3.3 V). The driver input signal that is applied to the TIN
pin is referenced to logic ground (GND). It is coupled across the
isolation barrier, inverted, and then appears at the transceiver
section, referenced to isolated ground (GNDISO). Similarly, the
receiver input (RIN) accepts RS-232 signal levels that are
referenced to isolated ground. The RIN input is inverted and
coupled across the isolation barrier to appear at the ROUT pin,
referenced to logic ground.
The digital signals are transmitted across the isolation barrier
using iCoupler technology. Chip-scale transformer windings
couple the digital signals magnetically from one side of the
barrier to the other. Digital inputs are encoded into waveforms
that are capable of exciting the primary transformer of the
winding. At the secondary winding, the induced waveforms are
decoded into the binary value that was originally transmitted.
There is hysteresis in the VCC input voltage detect circuit. Once the
dc-to-dc converter is active, the input voltage must be decreased
below the turn-on threshold to disable the converter. This feature
ensures that the converter does not go into oscillation due to
noisy input power.
+
C3
0.1F
10V
+ C1
0.1F
16V
+ C2
0.1F
16V
0.1F
+
C4
0.1F
16V
EIA/TIA-232E OUTPUT
EIA/TIA-232E INPUT
VISO
V+
C1+
C1–
TOUT
RIN
C2+
C2–
V–
GNDISO
07388-
014
ISOLATION
BARRIER
CMOS OUTPUT
CMOS INPUT
4.5V TO 5.5V
VCC
ROUT
TIN
GND
0.1F
ADM3251E
Figure 14. Typical Operating Circuit with the DC-to-DC Converter Enabled
(VCC = 4.5 V to 5.5 V)
+
C3
0.1F
10V
+ C1
0.1F
16V
+ C2
0.1F
16V
0.1F
+
C4
0.1F
16V
EIA/TIA-232E OUTPUT
EIA/TIA-232E INPUT
VISO
V+
C1+
C1–
TOUT
RIN
C2+
C2–
V–
GNDISO
07388-
015
ISOLATION
BARRIER
CMOS OUTPUT
CMOS INPUT
3.0V TO 3.7V
3.0V TO 5.5V
ISOLATED SUPPLY
VCC
ROUT
TIN
GND
0.1F
ADM3251E
Figure 15. Typical Operating Circuit with the DC-to-DC Converter Disabled
(VCC = 3.0 V to 3.7 V)
Rev. G | Page 11 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| ADM3252EABCZ | IC LINE DRIVER/RECEIVER |
| ADM3311EACPZ | IC TXRX RS-232 3:5 2.7V 32LFCSP |
| ADM3488EARZ | IC TXRX ESD RS-485 3.3V 8-SOIC |
| ADM3491ARU-1REEL7 | IC TXRX RS-485 HS 3.3V 16TSSOP |
| ADM3493ARZ-REEL7 | IC TXRX RS-422/485 3.3V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM3251EARWZ-REEL | 功能描述:IC LINE DVR/RCVR RS232 20-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP（0.209"，5.30mm 宽） 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2 |
| ADM3252E | 制造商:AD 制造商全称:Analog Devices 功能描述:Isolated, Dual Channel, RS-232 Line Driver/Receiver |
| ADM3252EABCZ | 功能描述:IC LINE DRIVER/RECEIVER RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:* 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ADM3260ARSZ | 功能描述:I2C Digital Isolator 2500Vrms 2 Channel 25kV/μs CMTI 20-SSOP (0.209", 5.30mm Width) 制造商:analog devices inc. 系列:IsoPower?，iCoupler? 包装:管件 零件状态:有效 技术:磁耦合 类型:I2C 隔离式电源:是 通道数:2 输入 - 输入侧 1/输入侧 2:2/2 通道类型:双向 电压 - 隔离:2500Vrms 共模瞬态抗扰度（最小值）:25kV/μs 数据速率:- 传播延迟 tpLH / tpHL（最大值）:- 脉宽失真（最大）:145ns，85ns 上升/下降时间（典型值）:- 电压 - 电源:3 V ~ 5.5 V 工作温度:-40°C ~ 105°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商器件封装:20-SSOP 标准包装:66 |
| ADM3260ARSZ-RL7 | 功能描述:I2C Digital Isolator 2500Vrms 2 Channel 25kV/μs CMTI 20-SSOP (0.209", 5.30mm Width) 制造商:analog devices inc. 系列:IsoPower?，iCoupler? 包装:剪切带（CT） 零件状态:有效 技术:磁耦合 类型:I2C 隔离式电源:是 通道数:2 输入 - 输入侧 1/输入侧 2:2/2 通道类型:双向 电压 - 隔离:2500Vrms 共模瞬态抗扰度（最小值）:25kV/μs 数据速率:- 传播延迟 tpLH / tpHL（最大值）:- 脉宽失真（最大）:145ns，85ns 上升/下降时间（典型值）:- 电压 - 电源:3 V ~ 5.5 V 工作温度:-40°C ~ 105°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商器件封装:20-SSOP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。