- 您现在的位置：买卖IC网 > PDF目录15385 > ADM693AN (Analog Devices Inc)IC SUPER MPU 4.4 100MA WD 16DIP PDF资料下载
参数资料
| 型号： | ADM693AN |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC SUPER MPU 4.4 100MA WD 16DIP |
| 标准包装： | 25 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 35 ms |
| 电压 - 阀值： | 4.4V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-PDIP |
| 包装： | 管件 |
ADM690–ADM695
CE Gating and RAM Write Protection (ADM691/ADM693/
ADM695)
The ADM691/ADM693/ADM695 products include memory
protection circuitry which ensures the integrity of data in mem-
ory by preventing write operations when V CC is at an invalid
level. There are two additional pins, CE IN and CE OUT , which
may be used to control the Chip Enable or Write inputs of
CMOS RAM. When V CC is present, CE OUT is a buffered replica
of CE IN , with a 5 ns propagation delay. When V CC falls below
the reset voltage threshold or V BATT , an internal gate forces
CE OUT high, independent of CE IN .
CE OUT typically drives the CE , CS , or write input of battery
backed up CMOS RAM. This ensures the integrity of the data
in memory by preventing write operations when V CC is at an in-
valid level. Similar protection of EEPROMs can be achieved by
using the CE OUT to drive the store or write inputs.
Power Fail Warning Comparator
An additional comparator is provided for early warning of failure
in the microprocessor’s power supply. The Power Fail Input
(PFI) is compared to an internal +1.3 V reference. The Power
Fail Output ( PFO ) goes low when the voltage at PFI is less than
1.3 V. Typically PFI is driven by an external voltage divider
which senses either the unregulated dc input to the system’s 5 V
regulator or the regulated 5 V output. The voltage divider ratio
can be chosen such that the voltage at PFI falls below 1.3 V sev-
eral milliseconds before the +5 V power supply falls below the
reset threshold. PFO is normally used to interrupt the micropro-
cessor so that data can be stored in RAM and the shut down
procedure executed before power is lost
INPUT
POWER
If the 5 ns typical propagation delay of CE OUT is excessive, con-
nect CE IN to GND and use the resulting CE OUT to control a
R 1
1.3V
PFO
POWER
FAIL
high speed external logic gate.
ADM69x
R 2
POWER
FAIL
INPUT
ADM69x
OUTPUT
CE IN
V CC LOW = 0
V CC OK = 1
CE OUT
Figure 7. Power Fail Comparator
Table II. Input and Output Status In Battery Backup Mode
Figure 5. Chip Enable Gating
Signal
Status
V CC
V2
V1
V2
V1
V OUT
V OUT is connected to V BATT via an internal
PMOS switch.
RESET
Logic low.
RESET
t 1
t 1
RESET
Logic high. The open circuit output voltage is
equal to V OUT .
LOW LINE
Logic low.
LOW LINE
CE IN
CE OUT
t 1 = RESET TIME.
V1 = RESET VOLTAGE THRESHOLD LOW
V2 = RESET VOLTAGE THRESHOLD HIGH
HYSTERESIS = V2–V1
Figure 6. Chip Enable Timing
BATT ON
WDI
WDO
PFI
PFO
CE IN
CE OUT
OSC IN
OSC SEL
–8 –
Logic high. The open circuit voltage is equal to
V OUT.
WDI is ignored. It is internally disconnected
from the internal pull-up resistor and does not
source or sink current as long as its input voltage
is between GND and V OUT . The input voltage
does not affect supply current.
Logic high. The open circuit voltage is equal
to V OUT .
The Power Fail Comparator is turned off and
has no effect on the Power Fail Output.
Logic low.
CE IN is ignored. It is internally disconnected
from its internal pull-up and does not source or
sink current as long as its input voltage is
between GND and V OUT . The input voltage
does not affect supply current.
Logic high. The open circuit voltage is equal to
V OUT .
OSC IN is ignored.
OSC SEL is ignored.
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| GCM31DTAI-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| VE-JWY-EX-F3 | CONVERTER MOD DC/DC 3.3V 49.5W |
| RBM30DRSI | CONN EDGECARD 60POS DIP .156 SLD |
| RMM12DSUI | CONN EDGECARD 24POS DIP .156 SLD |
| RBM36DCWI | CONN EDGECARD 72POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM693ANZ | 功能描述:IC SUPER MPU 4.4 100MA WD 16DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极，开路漏极 复位:高有效/低有效 复位超时:最小为 250 ms 电压 - 阀值:4.37V，4.62V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1337 (CN2011-ZH PDF) |
| ADM693ANZ | 制造商:Analog Devices 功能描述:IC SUPERVISORY CIRCUIT |
| ADM693AQ | 制造商:AD 制造商全称:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
| ADM693AR | 功能描述:IC SUPER MPU 4.4 100MA WD 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM693AR-REEL | 功能描述:IC SUPERVISOR MPU 4.4V WD 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:400 系列:- 类型:备用电池电路 监视电压数目:1 输出:开路漏极，推挽式 复位:高有效/低有效 复位超时:最小为 35 ms 电压 - 阀值:4.65V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC W 包装:带卷 (TR) 其它名称:ADM691ARZ-REEL7TR |
发布紧急采购，3分钟左右您将得到回复。