- 您现在的位置：买卖IC网 > PDF目录20039 > ADN2847ACPZ-32-RL7 (Analog Devices Inc)IC LSR DRVR 3.3GBPS 3.6V 32LFCSP PDF资料下载
参数资料
| 型号： | ADN2847ACPZ-32-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC LSR DRVR 3.3GBPS 3.6V 32LFCSP |
| 标准包装： | 1,500 |
| 类型： | 激光二极管驱动器（光纤） |
| 数据速率： | 3.3Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 50mA |
| 电流 - 调制： | 80mA |
| 电流 - 偏置： | 100mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
Data Sheet
THEORY OF OPERATION
Laser diodes have current-in to light-out transfer functions, as
shown in Figure 9. Two key characteristics of this transfer
function are the threshold current, I TH , and the slope in the
linear region beyond the threshold current, referred to as slope
efficiency (LI).
ADN2847
where:
I AV is the average MPD current.
P CW is the dc optical power specified on the laser data sheet.
I MPD_CW is the MPD current at that specified P CW .
P AV is the average power required.
ER =
P1
P0
ER is the desired extinction ratio (ER = P1/P0).
P1
P AV =
P1 + P0
2
Note that I ERSET and I PSET changes from device to device; however,
the control loops determines actual values. It is not required to
P AV
? I
? P
LI =
? P
? I
know exact values for LI or MPD optical coupling.
LOOP BANDWIDTH SELECTION
For continuous operation, the user should hardwire the LBWSET
P0
I TH CURRENT
Figure 9. Laser Transfer Function
CONTROL
A monitor photodiode (MPD) is required to control the LD. The
pin high and use 1 μF capacitors to set the actual loop bandwidth.
These capacitors are placed between the PAVCAP pin and the
ERCAP pin and ground. It is important that these capacitors are
low leakage multilayer ceramics with an insulation resistance
greater than 100 GΩ or a time constant of 1000 seconds,
whichever is less.
MPD current is fed into the ADN2847 to control the power and
extinction ratio, continuously adjusting the bias current and
modulation current in response to the changing threshold
current and light-to-current slope efficiency of the laser.
Table 6.
Operation
Mode
Continuous
LBWSET
High
Recommended
PAVCAP
1 μF
Recommended
ERCAP
1 μF
The ADN2847 uses automatic power control (APC) to maintain
a constant average power over time and temperature.
50 Mbps to
3.3 Gbps
The ADN2847 uses closed-loop extinction ratio control to allow
Optimized for
2.5 Gbps to
Low
22 nF
22 nF
optimum setting of the extinction ratio for every device. Thus,
SONET/SDH interface standards can be met over device variation,
temperature, and laser aging. Closed-loop modulation control
eliminates the need to either overmodulate the LD or include
external components for temperature compensation. This
reduces research and development time and second sourcing
issues caused by characterizing LDs.
Average power and extinction ratio are set using the PSET pin
and the ERSET pin, respectively. Potentiometers are connected
between these pins and ground. The potentiometer R PSET is used
to change the average power. The potentiometer R ERSET is used
to adjust the extinction ratio. Both PSET and ERSET are kept
1.2 V above GND.
The R PSET and R ERSET potentiometers can be calculated using the
following formulas:
3.3 Gbps
Setting LBSET low and using 22 nF capacitors results in a
shorter loop time constant (a 10× reduction over using 1 μF
capacitors and keeping LBWSET high.)
ALARMS
The ADN2847 is designed to allow interface compliance to
ITUT-G958 (11/94) section 10.3.1.1.2 (transmitter fail) and
section 10.3.1.1.3 (transmitter degrade). The ADN2847 has two
active high alarms, DEGRADE and FAIL. A resistor between
ground and the ASET pin is used to set the current at which
these alarms are raised. The current through the ASET resistor
is a ratio of 100:1 to the FAIL alarm threshold. The DEGRADE
alarm is raised at 90% of this level.
Example:
( Ω )
R PSET =
R ERSET =
ER ? 1
ER + 1
I FAIL
I ASET =
= = 500 μA
R ASET =
=
= 2 . 4 k Ω
1 . 2 V
I AV
I MPD _ CW
P CW
1 . 2 V
×
× P AV
( Ω )
I FAIL = 50 mA so I DEGRADE = 45 mA
50 mA
100 100
1 . 2 V 1 . 2
I ASET 500 μA
where the smallest valid value for R ASET is 1.2 kΩ, because this
corresponds to the I BIAS maximum of 100 mA.
Rev. B | Page 9 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| ACB45DHFT | CONN EDGECARD 90POS .050 SMD |
| RMM36DRST | CONN EDGECARD 72POS DIP .156 SLD |
| T86C156K010EASS | CAP TANT 15UF 10V 10% 2312 |
| ABB45DHFT | CONN EDGECARD 90POS .050 SMD |
| GCM06DTAI-S189 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN2847ACPZ-48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADN2847CSURFC | 制造商:Analog Devices 功能描述: |
| ADN2848 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ADN2848: 3V Dual Loop 50Mbps to 622Mbps Laser Diode Driver Data Sheet (Rev. 0. 1/03) |
| ADN2848ACP-32 | 制造商:Analog Devices 功能描述:Laser Driver DFB 1.25Gbps 1-CH 32-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:155MBPS-622MBPS, 3V, LASER DIODE DRIVER - Bulk |
| ADN2848ACP-32-RL | 制造商:Analog Devices 功能描述:Laser Driver DFB 1.25Gbps 1-CH 32-Pin LFCSP EP T/R |
发布紧急采购，3分钟左右您将得到回复。