- 您现在的位置：买卖IC网 > PDF目录11788 > ADN8102ACPZ (Analog Devices Inc)IC EQUALIZER 4CH XSTREAM 64LFCSP PDF资料下载
参数资料
| 型号： | ADN8102ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC EQUALIZER 4CH XSTREAM 64LFCSP |
| 标准包装： | 1 |
| 系列： | XStream™ |
| 应用： | 以太网控制器 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 3.3 V |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADN8102
Rev. B | Page 29 of 36
PRINTED CIRCUIT BOARD (PCB) LAYOUT
GUIDELINES
The high speed differential inputs and outputs should be routed
with 100 Ω controlled impedance, differential transmission
lines. The transmission lines, either microstrip or stripline,
should be referenced to a solid low impedance reference plane.
An example of a PCB cross-section is shown in Figure 45. The
trace width (W), differential spacing (S), height above reference
plane (H), and dielectric constant of the PCB material determine
the characteristic impedance. Adjacent channels should be kept
apart by a distance greater than 3 W to minimize crosstalk.
PCB DIELECTRIC
SIGNAL (MICROSTRIP)
SOLDERMASK
PCB DIELECTRIC
REFERENCE PLANE
SIGNAL (STRIPLINE)
W
S
W
H
W
S
W
0
70
60
-1
49
Figure 45. Example of a PCB Cross-Section
Power Supply Connections and Ground Planes
Use of one low impedance ground plane is recommended.
The VEE pins should be soldered directly to the ground plane
to reduce series inductance. If the ground plane is an internal
plane and connections to the ground plane are made through
vias, multiple vias can be used in parallel to reduce the series
inductance. The exposed pad should be connected to the VEE
plane using plugged vias so that solder does not leak through
the vias during reflow.
Use of a 10 μF electrolytic capacitor between VCC and VEE is
recommended at the location where the 3.3 V supply enters the
printed circuit board (PCB). It is recommended that 0.1 μF and
1 nF ceramic chip capacitors be placed in parallel at each supply
pin for high frequency, power supply decoupling. When using
0.1 μF and 1 nF ceramic chip capacitors, they should be placed
between the IC power supply pins (VCC, VTTI, and VTTO)
and VEE, as close as possible to the supply pins.
By using adjacent power supply and GND planes, excellent high
frequency decoupling can be realized by using close spacing
between the planes. This capacitance is given by
CPLANE = 0.88εr × A/d (pF)
where:
εr is the dielectric constant of the PCB material.
A is the area of the overlap of power and GND planes (cm2).
d is the separation between planes (mm).
For FR4, εr = 4.4 and 0.25 mm spacing, C ≈ 15 pF/cm2.
Supply Sequencing
Ideally, all power supplies should be brought up to the appropri-
ate levels simultaneously (power supply requirements are set by
the supply limits in Table 1 and the absolute maximum ratings
listed in Table 3). In the event that the power supplies to the
ADN8102 are brought up separately, the supply power-up
sequence is as follows: DVCC is powered first, followed by VCC,
and lastly VTTI and VTTO. The power-down sequence is reversed,
with VTTI and VTTO being powered off first.
VTTI and VTTO contain ESD protection diodes to the VCC power
current condition in these devices (ISUSTAINED < 64 mA), the VTTI
and VTTO supplies should be powered on after VCC and should
be powered off before VCC.
If the system power supplies have a high impedance in the
powered off state, then supply sequencing is not required
provided the following limits are observed:
Peak current from VTTI or VTTO to VCC < 200 mA.
Sustained current from VTTI or VTTO to VCC < 64 mA.
Thermal Paddle Design
The LFCSP is designed with an exposed thermal paddle to
conduct heat away from the package and into the PCB. By
incorporating thermal vias into the PCB thermal paddle,
heat is dissipated more effectively into the inner metal layers
of the PCB. To ensure device performance at elevated
temperatures, it is important to have a sufficient number of
thermal vias incorporated into the design. An insufficient
number of thermal vias results in a θJA value larger than
specified in Table 1. Additional PCB footprint and assembly
guidelines are described in the AN-772 Application Note, A
Design and Manufacturing Guide for the Lead Frame Chip Scale
Package (LFCSP).
It is recommended that a via array of 4 × 4 or 5 × 5 with a
diameter of 0.3 mm to 0.33 mm be used to set a pitch between
1.0 mm and 1.2 mm. A representative of these arrays is shown in
THERMAL
VIA
THERMAL
PADDLE
07
06
0-
1
50
Figure 46. PCB Thermal Paddle and Via
相关PDF资料 |
PDF描述 |
|---|---|
| AD7669ARZ | IC I/O PORT 8BIT ANALOG 28SOIC |
| 0510210200 | CONN HOUSING 2POS 1.25MM |
| AD9883ABSTZ-140 | IC INTERFACE FLAT 140MHZ 80LQFP |
| AD9888KSZ-140 | IC FLAT PANEL INTERFACE 128-MQFP |
| AD7569JNZ | IC I/O PORT 8BIT ANALOG 24DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN8102ACPZ-R7 | 功能描述:IC EQUALIZER 4CH XSTREAM 64LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:XStream™ 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| ADN8102-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:3.75 Gbps Quad Bidirectional CX4 Equalizer |
| ADN8102XCPZ | 功能描述:Ethernet Controller Interface 制造商:analog devices inc. 系列:XStream?? 包装:- 零件状态:上次购买时间 应用:以太网控制器 接口:I2C 电压 - 电源:1.8 ~ 3.3V 封装/外壳:- 供应商器件封装:- 安装类型:- 标准包装:1 |
| ADN8810 | 制造商:Analog Devices 功能描述:- Bulk |
| ADN8810ACP | 制造商:Analog Devices 功能描述:Current Source 24-Pin LFCSP EP |
发布紧急采购，3分钟左右您将得到回复。