- 您现在的位置：买卖IC网 > PDF目录16947 > ADP121CB-3.3-EVALZ (Analog Devices Inc)BOARD EVAL ADP121-1 3.3V OUTPUT PDF资料下载
参数资料
| 型号： | ADP121CB-3.3-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADP121-1 3.3V OUTPUT |
| 设计资源： | Low power, Long Range, ISM Wireless Measuring Node (CN0164) |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 150mA |
| 输入电压： | 2.3 ~ 5.5 V |
| 稳压器类型： | 正，固定式 |
| 工作温度： | -40°C ~ 125°C |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP121 |
ADP121
CURRENT LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP121 is protected against damage due to excessive
power dissipation by current and thermal overload protection
circuits. The ADP121 is designed to current limit when the
output load reaches 225 mA (typical). When the output load
Data Sheet
dissipation in the power device, and thermal resistances between
the junction-and-ambient air (θ JA ). The θ JA number is dependent
on the package assembly compounds used and the amount of
copper to which the GND pins of the package are soldered on the
PCB. Table 6 shows typical θ JA values for various PCB copper
sizes and Table 7 shows the typical Ψ JB values for the ADP121.
exceeds 225 mA, the output voltage is reduced to maintain a
constant current limit.
Table 6. Typical θ JA Values
Copper Size (mm 2 ) TSOT (°C/W)
WLCSP (°C/W)
Thermal overload protection is built-in, which limits the
junction temperature to a maximum of 150°C (typical). Under
extreme conditions (that is, high ambient temperature and
power dissipation) when the junction temperature starts to
rise above 150°C, the output is turned off, reducing the output
50
100
300
500
170
152
146
134
131
260
159
157
153
151
current to zero. When the junction temperature drops below
135°C, the output is turned on again and output current is
1
Device soldered to minimum size pin traces.
restored to its nominal value.
Table 7. Typical Ψ JB Values
Consider the case where a hard short from VOUT to GND occurs.
At first, the ADP121 current limits, so that only 225 mA is con-
TSOT (°C/W)
42.8
WLCSP (°C/W)
58.4
ducted into the short. If self-heating of the junction is great
enough to cause its temperature to rise above 150°C, thermal
shutdown activates turning off the output and reducing the
The junction temperature of the ADP121 can be calculated
from the following equation:
output current to zero. As the junction temperature cools and
drops below 135°C, the output turns on and conducts 225 mA
into the short, again causing the junction temperature to rise
above 150°C. This thermal oscillation between 135°C and
150°C causes a current oscillation between 225 mA and 0 mA
that continues as long as the short remains at the output.
T J = T A + ( P D × θ JA )
where:
T A is the ambient temperature.
P D is the power dissipation in the die, given by
P D = [( V IN ? V OUT ) × I LOAD ] + ( V IN × I GND )
(2)
(3)
Current and thermal limit protections are intended to protect
the device against accidental overload conditions. For reliable
operation, device power dissipation must be externally limited
so junction temperatures do not exceed 125°C.
THERMAL CONSIDERATIONS
In most applications, the ADP121 does not dissipate a lot of heat
due to high efficiency. However, in applications with a high
ambient temperature and high supply voltage to an output voltage
differential, the heat dissipated in the package is large enough
that it can cause the junction temperature of the die to exceed
the maximum junction temperature of 125°C.
When the junction temperature exceeds 150°C, the converter
enters thermal shutdown. It recovers only after the junction
temperature has decreased below 135°C to prevent any permanent
damage. Therefore, thermal analysis for the chosen application
is very important to guarantee reliable performance over all
conditions. The junction temperature of the die is the sum of
the ambient temperature of the environment and the tempera-
ture rise of the package due to the power dissipation, as shown
where:
I LOAD is the load current.
I GND is the ground current.
V IN and V OUT are input and output voltages, respectively.
Power dissipation due to ground current is quite small and
can be ignored. Therefore, the junction temperature equation
simplifies to
T J = T A + {[( V IN ? V OUT ) × I LOAD ] × θ JA } (4)
As shown in Equation 4, for a given ambient temperature,
input-to-output voltage differential, and continuous load
current, there exists a minimum copper size requirement for
the PCB to ensure that the junction temperature does not rise
above 125°C. Figure 34 to Figure 47 show junction temperature
calculations for different ambient temperatures, load currents,
V IN -to-V OUT differentials, and areas of PCB copper.
In cases where the board temperature is known, the thermal
characterization parameter, Ψ JB , can be used to estimate the
junction temperature rise. T J is calculated from T B and P D using
the formula
in Equation 2.
To guarantee reliable operation, the junction temperature of the
ADP121 must not exceed 125°C. To ensure that the junction
temperature stays below this maximum value, the user needs to
be aware of the parameters that contribute to junction temperature
changes. These parameters include ambient temperature, power
Rev. G | Page 14 of 20
T J = T B + ( P D × Ψ JB )
(5)
相关PDF资料 |
PDF描述 |
|---|---|
| EYM18DTMH-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| 814554-000 | BOOT MOLDED |
| 234A132-25-0 | BOOT MOLDED |
| MIC2026-1BM TR | IC SW DISTRIBUTION 2CHAN 8SOIC |
| SRR1208-101YL | INDUCTOR HP 100UH 15% SHIELD SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP121UJZ-REDYKIT | 功能描述:KIT REDI TOOL 2.8/3.3 ADP121 RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:Redykit™ 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP122 | 制造商:AD 制造商全称:Analog Devices 功能描述:5.5 V Input, 300 mA, Low Quiescent Current, CMOS Linear Regulator |
| ADP1221 | 功能描述:板上安装压力/力传感器 34.3kPa 0.35kgf/cm Pressure Sensor RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
| ADP122-3.3-EVALZ | 功能描述:BOARD EVALUATION 3.3V ADP122 RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:- 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP122ACPZ-1.8-R7 | 功能描述:IC REG LDO 1.8V .3A 6LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 其它有关文件:LD39015JXX12 View All Specifications 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:1.2V 输入电压:1.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-WFBGA，FCBGA 供应商设备封装:4-覆晶（1.07x1.07） 包装:Digi-Reel® 其它名称:497-11958-6 |
发布紧急采购，3分钟左右您将得到回复。