- 您现在的位置：买卖IC网 > PDF目录16976 > ADP125-EVALZ (Analog Devices Inc)BOARD EVALUATION ADJUSTABLE V PDF资料下载
参数资料
| 型号： | ADP125-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION ADJUSTABLE V |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 输出电压： | 0.8 ~ 5 V |
| 电流 - 输出： | 500mA |
| 输入电压： | 2.3 ~ 5.5 V |
| 稳压器类型： | 正，可调式 |
| 工作温度： | -40°C ~ 85°C |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP125 |
ADP124/ADP125
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Output Capacitor
The ADP124/ADP125 are designed for operation with small,
space-saving ceramic capacitors, but these devices can function
with most commonly used capacitors as long as care is taken to
ensure an appropriate effective series resistance (ESR) value. The
ESR of the output capacitor affects the stability of the LDO control
loop. A minimum of 0.70 μF capacitance with an ESR of 1 ? or
less is recommended to ensure stability of the ADP124/ADP125.
The transient response to changes in load current is also affected by
the output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP124/ADP125 to
dynamic changes in load current. Figure 30 and Figure 31 show
the transient responses for output capacitance values of 1 μF and
4.7 μF, respectively.
Data Sheet
Input Bypass Capacitor
Connecting a 1 μF capacitor from VIN to GND reduces the circuit
sensitivity to the printed circuit board (PCB) layout, especially
when a long input trace or high source impedance is encountered.
If greater than 1 μF of output capacitance is required, the input
capacitor should be increased to match it.
Input and Output Capacitor Properties
Any good quality ceramic capacitors can be used with the
ADP124/ADP125, as long as the capacitor meets the minimum
capacitance and maximum ESR requirements. Ceramic capacitors
are manufactured with a variety of dielectrics, each with different
behavior over temperature and applied voltage. Capacitors must
have an adequate dielectric to ensure the minimum capacitance
over the necessary temperature range and dc bias conditions.
Using an X5R or X7R dielectric with a voltage rating of 6.3 V or
1
2
I OUT
1mA TO 500mA LOAD STEP
V OUT
V IN = 4V
V OUT = 3.3V
10 V is recommended. However, using Y5V and Z5U dielectrics
are not recommended for any LDO, due to their poor temperature
and dc bias characteristics.
teristics of an 0402, 1 μF, 10 V X5R capacitor. The voltage stability
of a capacitor is strongly influenced by the capacitor size and the
voltage rating. In general, a capacitor in a larger package or of a
higher voltage rating exhibits better stability. The temperature
variation of the X5R dielectric is about ±15% over the ?40°C to
+85°C temperature range and is not a function of package or
voltage rating.
CH1 500mA ? BW CH2 50.0mV
B
W
M400ns
A CH1
200mA
1.10
T
13.20%
1.05
Figure 30. Output Transient Response, C OUT = 1 μF
1.00
I OUT
1mA TO 500mA LOAD STEP
0.95
0.90
1
0.85
0.80
0.75
2
V OUT
0.70
0
1
2
3
4
5
6
7
BIAS VOLTAGE (V)
V IN = 4V
V OUT = 3.3V
Figure 32. Capacitance vs. Capacitor Voltage Bias Characteristics
CH1 500mA ? BW CH2 50.0mV
M400ns
A CH1
200mA
B
W
T 13.60%
Figure 31. Output Transient Response, C OUT = 4.7 μF
Equation 1 can be used to determine the worst-case capacitance,
accounting for capacitor variation over temperature, component
tolerance, and voltage.
C EFF = C × (1 ? TEMPCO ) × (1 ? TOL )
where:
C EFF is the effective capacitance at the operating voltage.
C is the rated capacitance value.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Rev. C | Page 12 of 20
(1)
相关PDF资料 |
PDF描述 |
|---|---|
| ECC35DJXN-S1136 | CONN EDGECARD 70PS .100 PRESSFIT |
| HBM12DRXI | CONN EDGECARD 24POS DIP .156 SLD |
| MIC94310-GYMT EV | BOARD EVAL FOR MIC94310-GYMT |
| LM285Z/NOPB | IC VREF SHUNT ADJ TO-92-3 |
| 3-1589472-6 | CONN PLUG 15POS 30AWG 10IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1261 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PRECISION SEMICONDUCTOR PRESSURE SENSOR |
| ADP1271 | 功能描述:板上安装压力/力传感器 490.3kPa 5.0kgf/cm Pressure Sensor RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
| ADP1281 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PRECISION SEMICONDUCTOR PRESSURE SENSOR |
| ADP1290ACBZ-R7 | 功能描述:IC LOAD SWITCH HIGH SIDE 6WLCSP 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 开关类型:通用 输出数:1 比率 - 输入:输出:1:1 输出配置:高端 输出类型:N 通道 接口:开/关 电压 - 负载:2.3 V ~ 13.2 V 电压 - 电源（Vcc/Vdd）:不需要 电流 - 输出（最大值）:2A 导通电阻（典型值）:40 毫欧 输入类型:- 特性:- 故障保护:- 工作温度:-40°C ~ 105°C（TJ） 封装/外壳:6-WFBGA，WLCSP 供应商器件封装:6-WLCSP（1.45x0.95） 标准包装:1 |
| ADP1290CB-EVALZ | 功能描述:ADP1290 - Power Management, Power Distribution Switch (Load Switch) Evaluation Board 制造商:analog devices inc. 系列:- 零件状态:有效 主要用途:电源管理，配电开关（负载开关） 嵌入式:- 使用的 IC/零件:ADP1290 主要属性:1 通道（单路） 辅助属性:- 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。