- 您现在的位置：买卖IC网 > PDF目录20391 > ADP1612-5-EVALZ (Analog Devices Inc)BOARD EVAL ADP1612 5V VOUT PDF资料下载
参数资料
| 型号： | ADP1612-5-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADP1612 5V VOUT |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 5V |
| 电流 - 输出： | 1.4A |
| 输入电压： | 1.8 ~ 5.5 V |
| 稳压器拓扑结构： | 升压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP1612 |
| 产品目录页面： | 791 (CN2011-ZH PDF) |
| 相关产品： | ADP1612ARMZ-R7DKR-ND - IC REG BST SEPIC ADJ 1.4A 8MSOP ADP1612ARMZ-R7CT-ND - IC REG BST SEPIC ADJ 1.4A 8MSOP ADP1612ARMZ-R7TR-ND - IC REG BST SEPIC ADJ 1.4A 8MSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADP1612/ADP1613
Data Sheet
V OUT ? V IN ( MAX )
D MIN =
CHOOSING THE INPUT AND OUTPUT CAPACITORS
The ADP1612/ADP1613 require input and output bypass capa-
citors to supply transient currents while maintaining constant
input and output voltages. Use a low equivalent series resistance
(ESR), 10 μF or greater input capacitor to prevent noise at the
ADP1612/ADP1613 input. Place the capacitor between VIN
and GND as close to the ADP1612/ADP1613 as possible.
Ceramic capacitors are preferred because of their low ESR
characteristics. Alternatively, use a high value, medium ESR
capacitor in parallel with a 0.1 μF low ESR capacitor as close
to the ADP1612/ADP1613 as possible.
Ensure that the diode is rated to handle the average output
load current. Many diode manufacturers derate the current
capability of the diode as a function of the duty cycle. Verify
that the output diode is rated to handle the average output
load current with the minimum duty cycle. The minimum
duty cycle of the ADP1612/ADP1613 is
V OUT
where V IN(MAX) is the maximum input voltage.
The following are suggested Schottky diode manufacturers:
(12)
The output capacitor maintains the output voltage and supplies
current to the load while the ADP1612/ADP1613 switch is on.
?
?
ON Semiconductor
Diodes, Inc.
? V OUT =
Q C I OUT × t ON (8)
t ON =
D
V OUT ? V IN
? V IN
?
R
F Z ( RHP ) = ? ?
? × LOAD (13)
2 π × L
? V OUT
?
C OUT ≥
The value and characteristics of the output capacitor greatly
affect the output voltage ripple and stability of the regulator. A
low ESR ceramic dielectric capacitor is preferred. The output
voltage ripple ( ? V OUT ) is calculated as follows:
=
C OUT C OUT
where:
Q C is the charge removed from the capacitor.
t ON is the on time of the switch.
C OUT is the output capacitance.
I OUT is the output load current.
(9)
f SW
and
D = (10)
V OUT
Choose the output capacitor based on the following equation:
I OUT × ( V OUT ? V IN ) (11)
f SW × V OUT × ? V OUT
LOOP COMPENSATION
The ADP1612/ADP1613 use external components to
compensate the regulator loop, allowing optimization of
the loop dynamics for a given application.
The step-up converter produces an undesirable right-half plane
zero in the regulation feedback loop. This requires compensating
the regulator such that the crossover frequency occurs well
below the frequency of the right-half plane zero. The right-
half plane zero is determined by the following equation:
2
?
where:
F Z (RHP) is the right-half plane zero.
R LOAD is the equivalent load resistance or the output voltage
divided by the load current.
To stabilize the regulator, ensure that the regulator crossover
frequency is less than or equal to one-fifth of the right-half
plane zero.
The regulator loop gain is
Multilayer ceramic capacitors are recommended for this
application.
A VL =
V FB
V OUT
×
V IN
V OUT
× G MEA × R OUT || Z COMP × G CS × Z OUT
(14)
DIODE SELECTION
The output rectifier conducts the inductor current to the output
capacitor and load while the switch is off. For high efficiency,
minimize the forward voltage drop of the diode. For this reason,
Schottky rectifiers are recommended. However, for high voltage,
high temperature applications, where the Schottky rectifier
reverse leakage current becomes significant and can degrade
efficiency, use an ultrafast junction diode.
where:
A VL is the loop gain.
V FB is the feedback regulation voltage, 1.235 V.
V OUT is the regulated output voltage.
V IN is the input voltage.
G MEA is the error amplifier transconductance gain.
R OUT is 125 M?.
Z COMP is the impedance of the series RC network from COMP
to GND.
G CS is the current sense transconductance gain (the inductor
current divided by the voltage at COMP), which is internally
set by the ADP1612/ADP1613.
Z OUT is the impedance of the load in parallel with the output
capacitor.
Rev. D | Page 14 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| R0.25D12-3.315/H-R | CONV DC/DC 0.25W 3.3V +/-15VOUT |
| SDR1005-470KL | INDUCTOR 47UH SMD POWER |
| MLK0603L3N9S | INDUCTOR 3.9NH +-.3NH FIXED 0201 |
| T95C107M016LSSL | CAP TANT 100UF 16V 20% 2812 |
| VI-B3D-CX-F4 | CONVERTER MOD DC/DC 85V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1612ARMZ-R7 | 功能描述:IC REG BST SEPIC ADJ 1.4A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| ADP1612-BL1-EVZ | 制造商:Analog Devices 功能描述:BLANK ADISIMPOWER EVAL ADP1612 - Boxed Product (Development Kits) |
| ADP1612-BL2-EVZ | 制造商:Analog Devices 功能描述:BLANK SEPIC DEMO BOARD - Boxed Product (Development Kits) |
| ADP1612-BL3-EVZ | 功能描述:EVAL BLANK ADISIMPOWER ADP1612 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ADP1613 | 制造商:AD 制造商全称:Analog Devices 功能描述:650 kHz /1.3 MHz Step-Up PWM DC-to-DC Switching Converters |
发布紧急采购，3分钟左右您将得到回复。