- 您现在的位置：买卖IC网 > PDF目录16945 > ADP1741-EVALZ (Analog Devices Inc)BOARD EVAL 2A ADP1741 PDF资料下载
参数资料
| 型号： | ADP1741-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL 2A ADP1741 |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 输出电压： | 0.75 ~ 3V |
| 电流 - 输出： | 2A |
| 输入电压： | 1.6 ~ 3.6V |
| 稳压器类型： | 正，可调式 |
| 工作温度： | -40°C ~ 125°C |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP1741 |
| 产品目录页面： | 794 (CN2011-ZH PDF) |
| 相关产品： | ADP1741ACPZ-R7DKR-ND - IC REG LDO ADJ 2A 16LFCSP ADP1741ACPZ-R7CT-ND - IC REG LDO ADJ 2A 16LFCSP ADP1741ACPZ-R7TR-ND - IC REG LDO ADJ 2A 16LFCSP |
Data Sheet
In this example, the worst-case temperature coefficient
(TEMPCO) over ?40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
Substituting these values in Equation 3 yields
C EFF = 4.46 μF × (1 ? 0.15) × (1 ? 0.1) = 3.41 μF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over temper-
ature and tolerance at the chosen output voltage.
To guarantee the performance of the ADP1740/ADP1741,
it is imperative that the effects of dc bias, temperature, and
tolerances on the behavior of the capacitors be evaluated for
each application.
UNDERVOLTAGE LOCKOUT
ADP1740/ADP1741
THERMAL CONSIDERATIONS
To guarantee reliable operation, the junction temperature of the
ADP1740/ADP1741 must not exceed 125°C. To ensure that the
junction temperature stays below this maximum value, the user
needs to be aware of the parameters that contribute to junction
temperature changes. These parameters include ambient tem-
perature, power dissipation in the power device, and thermal
resistance between the junction and ambient air (θ JA ). The θ JA
value is dependent on the package assembly compounds used
and the amount of copper to which the GND pin and the exposed
pad (EP) of the package are soldered on the PCB. Table 6 shows
typical θ JA values for the 16-lead LFCSP for various PCB copper
sizes. Table 7 shows typical Ψ JB values for the 16-lead LFCSP.
Table 6. Typical θ JA Values
Copper Size (mm 2 ) θ JA (°C/W), LFCSP
The ADP1740/ADP1741 have an internal undervoltage lockout
circuit that disables all inputs and the output when the input
voltage is less than approximately 1.58 V. This ensures that the
ADP1740/ADP1741 inputs and the output behave in a predict-
able manner during power-up.
0 1
100
500
1000
6400
130
80
69
54
42
Device soldered to minimum size pin traces.
CURRENT-LIMIT AND THERMAL OVERLOAD
PROTECTION
The ADP1740/ADP1741 are protected against damage due to
excessive power dissipation by current-limit and thermal
overload protection circuits. The ADP1740/ADP1741 are
designed to reach current limit when the output load reaches
3 A (typical). When the output load exceeds 3 A, the output
1
Table 7. Typical Ψ JB Values
Copper Size (mm 2 ) Ψ JB (°C/W) @ 1 W
100 32.7
500 31.5
1000 25.5
voltage is reduced to maintain a constant current limit.
Thermal overload protection is included, which limits the
junction temperature to a maximum of 150°C (typical). Under
extreme conditions (that is, high ambient temperature and power
dissipation) when the junction temperature begins to rise above
150°C, the output is turned off, reducing the output current to
zero. When the junction temperature drops below 135°C
The junction temperature of the ADP1740/ADP1741 can be
calculated from the following equation:
T J = T A + ( P D × θ JA )
where:
T A is the ambient temperature.
P D is the power dissipation in the die, given by
(4)
(typical), the output is turned on again and output current is
restored to its nominal value.
Consider the case where a hard short from VOUT to ground
occurs. At first, the ADP1740/ADP1741 reach current limit so
that only 3 A is conducted into the short. If self-heating of the
junction becomes great enough to cause its temperature to rise
above 150°C, thermal shutdown activates, turning off the output
and reducing the output current to zero. As the junction temper-
ature cools and drops below 135°C, the output turns on and
conducts 3 A into the short, again causing the junction temper-
ature to rise above 150°C. This thermal oscillation between
135°C and 150°C causes a current oscillation between 3 A and
0 A that continues as long as the short remains at the output.
Current-limit and thermal overload protections are intended to
protect the device against accidental overload conditions. For
reliable operation, device power dissipation should be externally
limited so that junction temperatures do not exceed 125°C.
P D = [( V IN ? V OUT ) × I LOAD ] + ( V IN × I GND ) (5)
where:
V IN and V OUT are the input and output voltages, respectively.
I LOAD is the load current.
I GND is the ground current.
Power dissipation due to ground current is quite small and can
be ignored. Therefore, the junction temperature equation can
be simplified as follows:
T J = T A + {[( V IN ? V OUT ) × I LOAD ] × θ JA } (6)
As shown in Equation 6, for a given ambient temperature, input-
to-output voltage differential, and continuous load current, a
minimum copper size requirement exists for the PCB to ensure
through Figure 41 show junction temperature calculations for
different ambient temperatures, load currents, V IN to V OUT
differentials, and areas of PCB copper.
Rev. F | Page 15 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| ADP170-1.8-EVALZ | BOARD EVAL ADP170 1.8V |
| ADP171-EVALZ | BOARD EVAL ADP171 1V |
| VE-JVM-EY | CONVERTER MOD DC/DC 10V 50W |
| VI-24L-EY | CONVERTER MOD DC/DC 28V 50W |
| CBC2012T220M | INDUCTOR 22UH 20% 0805 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1752 | 制造商:AD 制造商全称:Analog Devices 功能描述:0.8 A, Low VIN, Low Dropout Linear Regulator |
| ADP1752-1.5-EVALZ | 功能描述:BOARD EVAL AD1752 1.5V RoHS:是 类别:编程器，开发系统 >> 评估板 - 线性稳压器 (LDO) 系列:- 产品变化通告:1Q2012 Discontinuation 30/Mar/2012 设计资源:NCP590MNDPTAGEVB Gerber Files 标准包装:1 系列:- 每 IC 通道数:2 - 双 输出电压:1.8V，2.8V 电流 - 输出:300mA 输入电压:2.1 ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 85°C 板类型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名称:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS |
| ADP1752ACPZ-0.75R7 | 功能描述:IC REG LDO 0.75V .8A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| ADP1752ACPZ-1.0-R7 | 功能描述:IC REG LDO 1V .8A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
| ADP1752ACPZ-1.1-R7 | 功能描述:IC REG LDO 1.1V .8A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:0.1V @ 200mA 稳压器数量:2 电流 - 输出:300mA 电流 - 限制（最小）:350mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-UFQFN 供应商设备封装:8-MLPQ-UT（1.5x1.5） 包装:剪切带 (CT) 产品目录页面:1358 (CN2011-ZH PDF) 其它名称:SC560HULCT |
发布紧急采购，3分钟左右您将得到回复。