- 您现在的位置：买卖IC网 > PDF目录17391 > ADP2147CB-130EVALZ (Analog Devices Inc)BOARD EVAL ADP2147ACBZ-130 PDF资料下载
参数资料
| 型号： | ADP2147CB-130EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADP2147ACBZ-130 |
| 标准包装： | 1 |
| 系列： | * |
ADP2147
THEORY OF OPERATION
PWM
COMP
GM ERROR
AMP
VOUT
SOFT START
PSM
COMP
PWM/
PSM
CONTROL
I LIMIT
VIN
LOW
CURRENT
SW
VSEL
OSCILLATOR
UNDERVOLTAGE
LOCKOUT
DRIVER
AND
ANTISHOOT-
THROUGH
ADP2147
THERMAL
SHUTDOWN
EN
Figure 33. Functional Block Diagram
GND
The ADP2147 is a step-down dc-to-dc regulator that uses a
fixed frequency and high speed current-mode architecture.
The high switching frequency and tiny 6-ball WLCSP package
enable a small step-down dc-to-dc regulator solution.
The ADP2147 operates with an input voltage of 2.3 V to 5.5 V
and regulates an output voltage down to 0.8 V.
CONTROL SCHEME
The ADP2147 operates with a fixed frequency, current-mode
PWM control architecture at medium to high loads for high
efficiency but shifts to a power save mode control scheme at
light loads to lower the regulation power losses. When operating in
PWM mode, the duty cycle of the integrated switches is adjusted
and regulates the output voltage. When operating in power save
mode at light loads, the output voltage is controlled in a hyster-
etic manner, with higher V OUT ripple. During part of this time,
the converter is able to stop switching and enters an idle mode,
which improves conversion efficiency.
PWM MODE
In PWM mode, the ADP2147 operates at a fixed frequency of
3 MHz, set by an internal oscillator. At the start of each oscillator
cycle, the pFET switch is turned on, sending a positive voltage
across the inductor. Current in the inductor increases until the
magnitude of the current sense signal crosses the peak inductor
current threshold. This turns off the pFET switch and turns on the
nFET synchronous rectifier, which sends a negative voltage across
the inductor, causing the inductor current to decrease. The
synchronous rectifier stays on for the rest of the cycle.
POWER SAVE MODE
The ADP2147 smoothly transitions to the power save mode of
operation when the load current decreases below the power
save mode current threshold. When the ADP2147 enters power
save mode, an offset is induced in the PWM regulation level,
which makes the output voltage rise. When the output voltage
reaches a level approximately 1.5% above the PWM regulation
level, PWM operation turns off. At this point, both power
switches are off, and the ADP2147 enters idle mode. C OUT
discharges until V OUT falls to the PWM regulation voltage, at
which point the device drives the inductor to cause V OUT to rise
again to the upper threshold. This process is repeated for as long as
the load current is below the power save mode current
threshold.
Power Save Mode Current Threshold
The power save mode current threshold is set to 100 mA. The
ADP2147 employs a scheme that ensures that this current is
accurately controlled and independent of V IN and V OUT levels.
The control scheme also ensures that there is very little hysteresis
between the power save mode current threshold and that of the
PWM mode. The power save mode current threshold is opti-
mized for excellent efficiency across all load currents.
ENABLE/SHUTDOWN
The ADP2147 starts operating with soft start when the EN pin
is toggled from logic low to logic high. Pulling the EN pin low
forces the device into shutdown mode, reducing the supply
current to 0.2 μA (typical).
The ADP2147 regulates the output voltage by adjusting the peak
inductor current threshold.
Rev. 0 | Page 11 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| RCC07DRTN-S13 | CONN EDGECARD 14POS .100 EXTEND |
| TH3E107M016D0600 | CAP TANT 100UF 16V 20% 2917 |
| SJA7501-1-50-WHITE | LOOP WHITE 1" X 50YD X 0.12" |
| ADP2147CB-110EVALZ | BOARD EVAL ADP2147ACBZ-110 |
| RCC07DRTH-S13 | CONN EDGECARD 14POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2147CB-150EVALZ | 功能描述:BOARD EVAL ADP2147ACBZ-150 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADP2147CB-170EVALZ | 功能描述:BOARD EVAL ADP2147ACBZ-170 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADP2164 | 制造商:AD 制造商全称:Analog Devices 功能描述:6.5 V, 4 A, High Efficiency |
| ADP2164ACPZ-1.0-R7 | 功能描述:IC REG BUCK SYNC 1V 4A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP2164ACPZ-1.2-R7 | 功能描述:IC REG BUCK SYNC 1.2V 4A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。