- 您现在的位置：买卖IC网 > PDF目录17391 > ADP2147CB-130EVALZ (Analog Devices Inc)BOARD EVAL ADP2147ACBZ-130 PDF资料下载
参数资料
| 型号： | ADP2147CB-130EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADP2147ACBZ-130 |
| 标准包装： | 1 |
| 系列： | * |
ADP2147
APPLICATIONS INFORMATION
EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Inductor
The high switching frequency of the ADP2147 allows for the
selection of small chip inductors. For best performance, use
inductor values between 0.7 μH and 3 μH. Recommended
The peak-to-peak inductor current ripple is calculated using
the following equation:
Ceramic capacitors are manufactured with a variety of dielectrics,
each with different behavior over temperature and applied voltage.
Capacitors must have a dielectric adequate to ensure the
minimum capacitance over the necessary temperature range
and dc bias conditions. X5R or X7R dielectrics with a voltage
rating of 6.3 V or 10 V are recommended for best performance.
Y5V and Z5U dielectrics are not recommended for use with any
dc-to-dc regulator because of their poor temperature and dc bias
characteristics.
The worst-case capacitance, accounting for capacitor variation
over temperature, component tolerance, and voltage, is
calculated using the following equation:
C EFF = C OUT × (1 ? TEMPCO ) × (1 ? TOL )
V × ( V IN ? V OUT )
I RIPPLE
= OUT
V IN × f SW × L
where:
C EFF is the effective capacitance at the operating voltage.
where:
f SW is the switching frequency.
L is the inductor value.
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient (TEMPCO)
over ?40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
I PEAK = I LOAD ( MAX ) +
I RIPPLE
2
Substituting these values in the equation yields
C EFF = 4.0466 μF × (1 ? 0.15) × (1 ? 0.1) = 3.0956 μF
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal DCR.
Larger sized inductors have smaller DCR, which may decrease
inductor conduction losses. Inductor core losses are related to
the magnetic permeability of the core material. Because the
ADP2147 is a high switching frequency dc-to-dc regulator,
shielded ferrite core material is recommended for its low core
shows the suggested inductors that can be used for different
output current requirements; several inductors are also listed to
minimize PCB space for small current applications.
Table 6. Suggested 1.0 μH Inductors
To guarantee the performance of the ADP2147, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
6
5
4
3
2
Vendor
Model
Dimensions
(mm)
I SAT
(mA)
DCR
(mΩ)
1
Murata
LQM2MPN1R0NG0B
LQM18PN1R0
2.0 × 1.6 × 0.9
1.6 × 0.8 × 0.33
1400
700
85
52
0
0
1
2 3 4
5
6
Coilcraft?
Toko
TDK
Taiyo Yuden
EPL2014-102ML
0603LS-102
MDT2520-CN
GLFR1608T1R0M-LR
CBMF1608T1R0M
2.0 × 2.0 × 1.4
1.8 × 1.27 × 1.1
2.5 × 2.0 × 1.2
1.6 × 0.8 × 0.8
1.6 × 0.8 × 0.8
900
400
1800
360
290
59
81
100
80
90
DC BIAS VOLTAGE (V)
Figure 34. Typical Capacitor Performance
The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:
Output Capacitor
Increasing the value of the output capacitor reduces the output
voltage ripple and improves load transient response. When
V RIPPLE =
V IN
( 2 π × f SW ) × 2 × L × C OUT
=
I RIPPLE
8 × f SW × C OUT
choosing the capacitor value, it is also important to account for
the loss of capacitance due to dc output voltage bias.
Rev. 0 | Page 13 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| RCC07DRTN-S13 | CONN EDGECARD 14POS .100 EXTEND |
| TH3E107M016D0600 | CAP TANT 100UF 16V 20% 2917 |
| SJA7501-1-50-WHITE | LOOP WHITE 1" X 50YD X 0.12" |
| ADP2147CB-110EVALZ | BOARD EVAL ADP2147ACBZ-110 |
| RCC07DRTH-S13 | CONN EDGECARD 14POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2147CB-150EVALZ | 功能描述:BOARD EVAL ADP2147ACBZ-150 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADP2147CB-170EVALZ | 功能描述:BOARD EVAL ADP2147ACBZ-170 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADP2164 | 制造商:AD 制造商全称:Analog Devices 功能描述:6.5 V, 4 A, High Efficiency |
| ADP2164ACPZ-1.0-R7 | 功能描述:IC REG BUCK SYNC 1V 4A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| ADP2164ACPZ-1.2-R7 | 功能描述:IC REG BUCK SYNC 1.2V 4A 16LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。