- 您现在的位置：买卖IC网 > PDF目录14901 > ADP2302ARDZ-3.3-R7 (Analog Devices Inc)IC REG BUCK 3.3V 2A 8SOIC PDF资料下载
参数资料
| 型号： | ADP2302ARDZ-3.3-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 2A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 3 V ~ 20 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 700kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SOIC-EP |
| 其它名称： | ADP2302ARDZ-3.3-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
ADP2302/ADP2303
22
20
V IN
VIN
18
16
M AXIMUM INPUT VOLTAG E
R EN1
ADP2302/
ADP2303
14
12
10
R EN2
EN
8
Figure 49. Precision Enable Used as a Programmable UVLO
6
4
2
0
2
M INIMUM INPUT VOLTAGE
4 6 8 10
12
14
16
The precision enable feature also allows the ADP2302/ADP2303 to
be sequenced precisely by using a resistive voltage divider from
V OUT (V)
Figure 47. Voltage Conversion Limitations
LOW INPUT VOLTAGE CONSIDERATIONS
For low input voltage between 3 V and 5 V, the internal boot
ADP2302/
ADP2303
regulator cannot provide enough bootstrap voltage due to the
internal dropout voltage. As a result, the increased MOSFET
R DS(ON) reduces the available load current. To prevent this, add
ANOTHER
DC/DC
SUPPLIER
R EN1
R EN2
EN
an external small-signal Schottky diode from a 5.0 V external
V STARTUP ? ? ?
? 1 . 2 μA ? ? ? R EN1 ? 1 . 2 V
bootstrap bias voltage. Because the absolute maximum rating
between the BST and SW pins is 6.0 V, the bias voltage should
be less than 5.5 V. Figure 48 shows the application diagram for
the external bootstrap circuit.
SCHOTTKY
3.0V ~ 5.0V DIODE
VIN BST
ADP2302/ 5V BIAS VOLTAGE
ADP2303
SW
Figure 50. Precision Enable Used as a Sequencing Control
from Another DC-to-DC Power Supply
With a 1.2 μA pull-down current on the EN pin, the equation for
the start-up voltage in Figure 49 and Figure 50 is
? 1 . 2 V ?
? R EN2 ?
where:
V STARTUP is the start-up voltage to enable the chip.
OFF
ON
EN
FB
R EN1 is the resistor from the dc source to EN.
R EN2 is the resistor from EN to GND.
? ? ?
( V IN ? V OUT ) ? V OUT ? V D ?
? I RIPPLE ?
?
GND
Figure 48. External Bootstrap Circuit for Low Input Voltage Application
PROGRAMMING THE PRECISION ENABLE
Generally, the EN pin can connect to the VIN pin so that the
device automatically starts up when the input power is applied.
However, the precision enabling feature allows the ADP2302/
ADP2303 to be used as a programmable UVLO by connecting
a resistive voltage divider to VIN, as shown in Figure 49. This
configuration prevents the start-up problems that can occur
when VIN ramps up slowly in soft start with a relatively high
load current.
INDUCTOR
The high switching frequency of the ADP2302/ADP2303 allows
the use of small inductors. For best performance, use inductor
values between 1 μH and 15 μH.
The peak-to-peak inductor ripple current is calculated using the
following equation:
?
L ? f sw ? V IN ? V D ?
where:
f SW is the switching frequency.
L is the inductor value.
V D is the diode forward drop.
V IN is the input voltage.
V OUT is the output voltage.
Inductors of smaller values are usually smaller in size but
increase the ripple current and the output ripple voltage. As a
guideline, the inductor peak-to-peak ripple current is typically
set to 30% of the maximum load current for optimal transient
Rev. A | Page 17 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| LLS1H562MELA | CAP ALUM 5600UF 50V 20% SNAP |
| CDRR105NP-100MC | INDUCTOR POWER 10UH 3A SMD |
| VI-B5H-EW | CONVERTER MOD DC/DC 52V 100W |
| RCM24DSEF-S243 | CONN EDGECARD 48POS .156 EYELET |
| LKS1E472MESA | CAP ALUM 4700UF 25V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2302ARDZ-5.0 | 制造商:AD 制造商全称:Analog Devices 功能描述:2 A/3 A, 20 V, 700 kHz, Nonsynchronous Step-Down Regulators |
| ADP2302ARDZ-5.0-R7 | 功能描述:IC REG BUCK 5V 2A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| ADP2302ARDZ-R7 | 功能描述:IC REG BUCK ADJ 2A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| ADP2302-EVALZ | 功能描述:EVAL BOARD FOR ADP2302 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ADP2303 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA |
发布紧急采购，3分钟左右您将得到回复。