- 您现在的位置：买卖IC网 > PDF目录67357 > ADRF6801ACPZ-R7 (ANALOG DEVICES INC) 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR PDF资料下载
参数资料
| 型号： | ADRF6801ACPZ-R7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 调制器/解调器 |
| 英文描述： | 750 MHz - 1150 MHz RF/MICROWAVE I/Q DEMODULATOR |
| 封装： | 6 X 6 MM, ROHS COMPLIANT, MO-220VJJD-2, CP-40-1, LFSCP_VQ, 40 PIN |
| 文件页数： | 35/36页 |
| 文件大小： | 1034K |
| 代理商： | ADRF6801ACPZ-R7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页
ADRF6801
Rev. 0 | Page 8 of 36
Pin No.
Mnemonic
Description
5
RSET
Charge Pump Current. The nominal charge pump current can be set to 250 μA, 500 μA, 750 μA, or 1
mA using DB10 and DB11 of Register 4 and by setting DB18 to 0 (internal reference current). In this
mode, no external RSET is required. If DB18 is set to 1, the four nominal charge pump currents
(INOMINAL) can be externally tweaked according to the following equation where the resulting value is in
units of ohms.
8
.
37
4
.
217
×
=
NOMINAL
CP
SET
I
R
6
REFIN
Reference Input. Nominal input level is 1 V p-p. Input range is 10 MHz to 160 MHz.
8
MUXOUT
Multiplexer Output. This output can be programmed to provide the reference output signal or
the lock detect signal. The output is selected by programming the appropriate register.
9
DECL2
Decoupling Node for 2.5 V LDO. Connect a 0.1 μF capacitor between this pin and ground.
10
VCC2
The 5 V power supply pin for the 2.5 V LDO.
12
DATA
Serial Data Input. The serial data is loaded MSB first with the three LSBs being the control bits.
13
CLK
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is
latched into the 24-bit shift register on the CLK rising edge. Maximum clock frequency is 20 MHz.
14
LE
Load Enable. When the LE input pin goes high, the data stored in the shift registers is loaded into
one of the six registers, the relevant latch being selected by the first three control bits of the 24-bit
word.
17, 34
VCCLO
The 5 V Power Supply for the LO Path Blocks.
18, 19
QBBP, QBBN
Demodulator Q-Channel Differential Baseband Outputs; Differential Output Impedance of 24 Ω.
22, 29
VCCBB
The 5 V Power Supply for the Baseband Output Section of the Demodulator Blocks.
25
GNDRF
Ground Return for RF Input Balun.
26
RFIN
Single-Ended, Ground Referenced 50 Ω, RF Input.
27
VCCRF
The 5 V Power Supply for the RF Input Section of the Demodulator Blocks.
32, 33
IBBN, IBBP
Demodulator I-Channel Differential Baseband Outputs; Differential Output Impedance of 24 Ω.
36
LOSEL
LO Select. Connect this pin to ground for the simplest operation and to completely control the LO
path and input/output direction from the register SPI programming.
For additional control without register reprogramming, this input pin can determine whether the
LOP and LON pins operate as inputs or outputs. LOP and LON become inputs if the LOSEL pin is
set low, the LDRV bit of Register 5 is set low, and the LXL bit of Register 5 is set high. The
externally applied LO drive must be at 2×LO frequency (and the LDIV bit of Register 5 (DB5) set
low). LON and LOP become outputs when LOSEL is high or if the LDRV bit of Register 5 (DB3) is set
high and the LXL bit of Register 5 (DB4) is set low. The output frequency is 2×LO frequency (and
the LDIV bit of Register 5 (DB5) must be set high). This pin should not be left floating.
37, 38
LON, LOP
Local Oscillator Input/Output. When these pins are used as output pins, a differential frequency
divided version of the internal VCO is available on these pins. When the internal LO generation is
disabled, an external M×LO frequency signal can be applied to these pins (where M corresponds
to the LO path divider setting). (Differential Input/Output Impedance of 50 Ω)
39
VTUNE
VCO Control Voltage Input. This pin is driven by the output of the loop filter. The nominal input
voltage range on this pin is 1.0 V to 2.8 V.
40
DECL1
Connect a 10 μF capacitor between this pin and ground as close to the device as possible
because this pin serves as the VCO supply and loop filter reference.
EP
Exposed Paddle. The exposed paddle should be soldered to a low impedance ground plane.
相关PDF资料 |
PDF描述 |
|---|---|
| ADT14GS-REEL | ANALOG TEMP SENSOR-VOLTAGE, 2.49-2.52V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT42GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.75V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT50GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.1-2V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT45GRT | ANALOG TEMP SENSOR-VOLTAGE, 0.1-2V, 3Cel, RECTANGULAR, SURFACE MOUNT |
| ADT6503SRJZN015RL7 | DIGITAL TEMP SENSOR-SINGLE TRIP POINT, 11BIT(s), 4Cel, RECTANGULAR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADRF6801-EVALZ | 功能描述:EVAL BOARD FOR ADRF6801 制造商:analog devices inc. 系列:- 零件状态:有效 类型:解调器 频率:750MHz ~ 1.15GHz 配套使用产品/相关产品:ADRF6801 所含物品:板 标准包装:1 |
| ADRF6806ACPZ-R7 | 功能描述:IC QUADRATURE DEMOD 40LFCSP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADRF6806-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) 制造商:Analog Devices 功能描述:EVAL 525MHZ QUAD DEMOD ADRF6806 制造商:Analog Devices 功能描述:ADRF6806, QUAD DEMOD, EVAL BOARD; Silicon Manufacturer:Analog Devices; Features:IQ Demodulator with Integrated Fractional-N PLL, Integrated PLL & VCO; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes 制造商:Analog Devices 功能描述:MODULATOR/DEMODULATOR |
| ADRF6807 | 制造商:AD 制造商全称:Analog Devices 功能描述:700 MHz to 1050 MHz Quadrature |
| ADRF6807ACPZ-R7 | 功能描述:IC QUADRATURE DEMOD 40LFCSP RoHS:是 类别:RF/IF 和 RFID >> RF 解调器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:解调器 LO 频率:- RF 频率:70MHz ~ 300MHz P1dB:-9dBm 增益:- 噪音数据:6.36dB 电流 - 电源:41.5mA 电源电压:2.7 V 封装/外壳:28-WFQFN 裸露焊盘 供应商设备封装:28-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。