- 您现在的位置：买卖IC网 > PDF目录17081 > ADS1259EVM-PDK (Texas Instruments)KIT PERFORMANCE DEMO FOR ADS1259 PDF资料下载
参数资料
| 型号： | ADS1259EVM-PDK |
| 厂商： | Texas Instruments |
| 文件页数： | 14/48页 |
| 文件大小： | 0K |
| 描述： | KIT PERFORMANCE DEMO FOR ADS1259 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 24 |
| 采样率（每秒）： | 14k |
| 数据接口： | 串行，SPI? |
| 工作温度： | -40°C ~ 125°C |
| 已用 IC / 零件： | ADS1259 |
| 已供物品： | 2 个板，文档，软件 |
| 其它名称： | 296-30635 ADS1259EVM-PDK-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
XTAL1/CLKIN
XTAL2
External
Clock
50W
C
1
Crystal
(7.3728MHz)
XTAL1/CLKIN
XTAL2
C
1
2
,C :5pFto20pF
C
2
SBAS424D
– JUNE 2009 – REVISED AUGUST 2011
External Clock
SYNCOUT
Figure 46 shows the external clock connection. The
SYNCOUT is a digital output pin intended to
clock is applied to XTAL1/CLKIN and XTAL2 floats.
synchronize the chopping frequency of the PGA280
Make sure a clean clock input is applied to the
to
the
sampling
frequency
of
the
ADS1259.
ADS1259, free of overshoot and glitches. A series
Synchronizing the PGA280 to the ADS1259 places
resistor often helps to reduce overshoot and should
the PGA280 chopped 1/f noise at an exact null in the
be placed close to the driving end of the clock
ADS1259 frequency response, where the PGA280 1/f
source.
noise is rejected.
SYNCOUT frequency is equal to the ADS1259 clock
rate divided by 8 (fSYNCOUT = fCLK/8). The output clock
is enabled by the register bit SYNCOUT. Disabling
the output stops the clock but the output remains
actively
driven
low.
In
power-down
mode,
the
SYNCOUT output becomes an input. As with all
digital inputs, the pin must not be allowed to float. An
Figure 46. External Clock Connection
external 1M
Ω pull-down resistor is recommended to
ground the input in power-down mode.
Crystal Oscillator
The SYNCOUT clock is reset when START is
received and whenever registers CONFIG[2:0] are
Figure 47 shows the crystal oscillator connection. The
changed.
Connect
SYNCOUT
to
the
PGA280
crystal connects to XTAL1/CLKIN and XTAL2 and the
SYNCIN pin through a 4.7k
Ω series resistor. Place
capacitors connect to ground. The crystal and
the resistor as close as possible to the ADS1259
capacitors should be placed close to the device pins
SYNCOUT pin.
with short, direct traces. Neither the XTAL1/CLKIN
nor the XTAL2 pins can be used to drive any other
logic. Table 5 lists the recommended crystal for the
SLEEP MODE
ADS1259. If using other crystals, verify the oscillator
SLEEP mode is started by sending the SLEEP
start-up behavior.
command. In SLEEP mode, the device enters a
reduced power state and only a minimum of circuitry
is kept active. The WAKEUP command exits the
SLEEP mode and after which 512 fCLK cycles are
counted
before
the
ADS1259
is
ready
for
communication. The register settings are unaffected
in SLEEP.
SLEEP does not change the RBIAS register bit. For
quick conversions after WAKEUP, keep the internal
Figure 47. Crystal Connection
reference bias on before entering SLEEP. Otherwise,
after exiting SLEEP mode, allow time for the
reference to settle. Alternatively, to minimize power
Table 5. Recommended Crystal
consumption during SLEEP, set the internal reference
MANUFACTURER
FREQUENCY
PART NUMBER
bias off prior to engaging SLEEP. Note that in SLEEP
ECS
7.3728MHz
ECS-73-18-10
mode the SPI timeout function is disabled.
BYPASS
The digital core of the ADS1259 is powered by an
internal low dropout regulator (LDO). The DVDD
supply is the LDO input and the BYPASS pin is the
LDO output. A 1
μF capacitor must be connected from
the LDO output to DGND. No other load current
should be drawn from the BYPASS pin.
Copyright
2009–2011, Texas Instruments Incorporated
21
相关PDF资料 |
PDF描述 |
|---|---|
| ECC18DRES | CONN EDGECARD 36POS .100 EYELET |
| V24C5E125BL | CONVERTER MOD DC/DC 5V 125W |
| EVAL-AD5629RSDZ | BOARD EVAL FOR AD5629 |
| ADR292GRUZ-REEL7 | IC VREF SRS PREC 4.096V 8-TSSOP |
| ECC19DREN | CONN EDGECARD 38POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADS1259EVM-PDK | 制造商:Texas Instruments 功能描述:DEVELOPMENT TOOL |
| ADS1259IPW | 功能描述:模数转换器 - ADC Low-Noise 14kSPS 24B ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ADS1259IPW | 制造商:Texas Instruments 功能描述:A/D CONVERTER (A-D) IC |
| ADS1259IPWR | 功能描述:模数转换器 - ADC Low-Noise 14kSPS 24B ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ADS1259QPWRQ1 | 功能描述:24 Bit Analog to Digital Converter 1 Input 1 Sigma-Delta 20-TSSOP 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:有效 位数:24 采样率（每秒）:14k 输入数:1 输入类型:差分，单端 数据接口:SPI 配置:ADC 无线电 - S/H:ADC:- A/D 转换器数:1 架构:三角积分 参考类型:外部 电压 - 电源，模拟:5V 电压 - 电源，数字:2.7 V ~ 5.25 V 特性:PGA 工作温度:-40°C ~ 105°C 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:20-TSSOP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。