- 您现在的位置：买卖IC网 > PDF目录19380 > ADSP-2183KCAZ-210 (Analog Devices Inc)IC DSP 16BIT 52MHZ 144-BGA PDF资料下载
参数资料
| 型号： | ADSP-2183KCAZ-210 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 3/31页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 52MHZ 144-BGA |
| 标准包装： | 1 |
| 系列： | ADSP-21xx |
| 类型： | 定点 |
| 接口： | 同步串行端口（SSP） |
| 时钟速率： | 52MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 80kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 3.30V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LFBGA |
| 供应商设备封装： | 144-迷你型BGA |
| 包装： | 托盘 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
ADSP-2183
–11–
REV. C
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown
in Figure 7. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
12
34
56
78
910
11
12
13
14
GND
KEY (NO PIN)
RESET
BR
BG
TOP VIEW
EBG
EBR
ELOUT
EE
EINT
ELIN
ECLK
EMS
ERESET
Figure 7. Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1
× 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ-ICE
probe plug. Pin strip headers are available from vendors such as
3M, McKenzie, and Samtec.
Target Memory Interface
For your target system to be compatible with the EZ-ICE emu-
lator, it must comply with the memory interface guidelines
listed below.
PM, DM, BM, IOM and CM
Design your Program Memory (PM), Data Memory (DM),
Byte Memory (BM), I/O Memory (IOM), and Composite
Memory (CM) external interfaces to comply with worst case
device timing requirements and switching characteristics as
specified in the DSP’s data sheet. The performance of the
EZ-ICE may approach published worst case specification for
some memory access timing requirements and switching
characteristics.
Note: If your target does not meet the worst case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. De-
pending on the severity of the specification violation, you may
have trouble manufacturing your system as DSP components
statistically vary in switching characteristic and timing require-
ments within published limits.
Restriction: All memory strobe signals on the ADSP-2183
(
RD, WR, PMS, DMS, BMS, CMS and IOMS) used in your
target system must have 10 k
pull-up resistors connected
when the EZ-ICE is being used. The pull-up resistors are nec-
essary because there are no internal pull-ups to guarantee their
state during prolonged three-state conditions resulting from
typical EZ-ICE debugging sessions. These resistors may be
removed at your option when the EZ-ICE is not being used.
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals changes. Design your system to be compatible
with the following system interface signal changes introduced
by the EZ-ICE board:
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
RESET
signal.
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
BR signal.
EZ-ICE emulation ignores
RESET and BR when single-
stepping.
EZ-ICE emulation ignores
RESET and BR when in Emula-
tor Space (DSP halted).
EZ-ICE emulation ignores the state of target
BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (
BG) is asserted
by the EZ-ICE board’s DSP.
Target Architecture File
The EZ-ICE software lets you load your program in its linked
(executable) form. The EZ-ICE PC program can not load
sections of your executable located in boot pages (by the
linker). With the exception of boot page 0 (loaded into PM
RAM), all sections of your executable mapped into boot pages
are not loaded.
Write your target architecture file to indicate that only PM
RAM is available for program storage, when using the EZ-ICE
software’s loading feature. Data can be loaded to PM RAM or
DM RAM.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6670AUB50+T | IC TEMP SENSOR REMOTE 10-UMAX |
| MC7824CT | IC REG LDO 24V 1A TO220AB |
| GBC07DRTS | CONN EDGECARD 14POS DIP .100 SLD |
| ABE35DHRR | CONN CARD EXTEND 70POS 1MM SLD |
| RSC35DRSD-S273 | CONN EDGECARD 70POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP2183KS133 | 制造商:AD 功能描述:* |
| ADSP-2183KST-115 | 制造商:AD 制造商全称:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2183KST-133 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 33.3MHz 33.3MIPS 128-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:3.3V 16BITDSP,33MIPS,16KWRDSPM/DM,128TQF - Bulk |
| ADSP-2183KST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 128-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:3.3V,16BITDSP,40MIPS,16KWRDSPM/DM,128TQF - Bulk |
| ADSP-2183KST-210 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 52MHz 52MIPS 128-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:3.3V 16BITDSP,52MIPS,16KWORDSPM/DM,128TQ - Bulk 制造商:Analog Devices 功能描述:Digital Signal Processor IC |
发布紧急采购，3分钟左右您将得到回复。