- 您现在的位置：买卖IC网 > PDF目录1900 > ADSP-TS201SYBP-050 (Analog Devices Inc)IC PROCESSOR 500MHZ 576-SBGA PDF资料下载
参数资料
| 型号： | ADSP-TS201SYBP-050 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/48页 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR 500MHZ 576-SBGA |
| 标准包装： | 1 |
| 系列： | TigerSHARC® |
| 类型： | 定点/浮点 |
| 接口： | 主机接口，连接端口，多处理器 |
| 时钟速率： | 500MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 3MB |
| 电压 - 输入/输出： | 2.50V |
| 电压 - 核心： | 1.05V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 576-BBGA 裸露焊盘 |
| 供应商设备封装： | 576-BGA-ED（25x25） |
| 包装： | 托盘 |
| 配用： | ADZS-TS201S-EZLITE-ND - KIT LITE EVAL FOR ADSP-TS201S |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
ADSP-TS201S
Rev. C
|
Page 17 of 48
|
December 2006
Table 9. Pin Definitions—JTAG Port
Signal
Type
Term
Description
EMU
O/OD
nc
1
Emulation. Connected to the DSP’s JTAG emulator target board connector only.
TCK
I
epd or epu
Test Clock (JTAG). Provides an asynchronous clock for JTAG scan.
TDI
I (pu_ad)
nc1
Test Data Input (JTAG). A serial data input of the scan path.
TDO
O/T
nc1
Test Data Output (JTAG). A serial data output of the scan path.
TMS
I (pu_ad)
nc1
Test Mode Select (JTAG). Used to control the test state machine.
TRST
I/A (pu_ad)
na
Test Reset (JTAG). Resets the test state machine. TRST must be asserted or pulsed low
after power up for proper device operation. For more information, see Reset and
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
1 See the reference on Page 11 to the JTAG emulation technical reference EE-68.
Table 10. Pin Definitions—Flags, Interrupts, and Timer
Signal
Type
Term
Description
FLAG3–0
I/O/A
(pu)
nc
FLAG pins. Bidirectional input/output pins can be used as program conditions. Each pin
can be configured individually for input or for output. FLAG3–0 are inputs after power-up
and reset.
IRQ3–0
I/A
(pu)
nc
Interrupt Request. When asserted, the DSP generates an interrupt. Each of the IRQ3–0 pins
can be independently set for edge-triggered or level-sensitive operation. After reset, these
pins are disabled unless the IRQ3–0 strap option and interrupt vectors are initialized for
booting.
TMR0E
O
na
Timer 0 expires. This output pulses whenever timer 0 expires. At reset, this is a strap pin.
For more information, see Table 16 on Page 20.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-TS202SABPZ050 | IC PROCESSOR 500MHZ 576BGA |
| ADSP-TS203SABP-050 | IC DSP FLOAT/FIXED 500MHZ 576BGA |
| ADUC7021BCPZ62-RL7 | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| ADUC7023BCPZ62I-R7 | IC MCU 12BIT 62KB FLASH 32LFCSP |
| ADUC7024BCPZ62 | IC MCU FLSH 62K ANLG I/O 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-TS201SYBPZ050 | 功能描述:IC PROCESSOR 500MHZ 576-SBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:TigerSHARC® 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-TS202SABP-050 | 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 500MHz 500MIPS 576-Pin TEBGA 制造商:Analog Devices 功能描述:DSP FLOATING PT 32BIT 500MHZ 500MIPS 576PIN TEBGA - Trays |
| ADSP-TS202SABP-05X | 制造商:Analog Devices 功能描述: |
| ADSP-TS202SABP-X | 制造商:Analog Devices 功能描述: |
| ADSP-TS202SABPZ050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:TigerSHARC® 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。