- 您现在的位置：买卖IC网 > PDF目录67358 > ADT7476ARQZ-REEL7 (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | ADT7476ARQZ-REEL7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | ROHS COMPLIANT, MO-137AE, QSOP-24 |
| 文件页数： | 13/72页 |
| 文件大小： | 5219K |
| 代理商： | ADT7476ARQZ-REEL7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADT7476
Rev. B | Page 20 of 72
VID CODE MONITORING
The ADT7476 has five dedicated voltage ID (VID code) inputs.
These are digital inputs that can be read back through the VID
register (0x43) to determine the processor voltage required or
being used in the system. Five VID code inputs support VRM9.x
solutions. In addition, Pin 21 (12 V input) can be reconfigured as
a sixth VID input to satisfy future VRM requirements.
VID Code Register (0x43)
Bit 0 = VID0, reflects logic state of Pin 5.
Bit 1 = VID1, reflects logic state of Pin 6.
Bit 2 = VID2, reflects logic state of Pin 7.
Bit 3 = VID3, reflects logic state of Pin 8.
Bit 4 = VID4, reflects logic state of Pin 19.
Bit 5 = VID5, reconfigurable 12 V input. This bit reads 0 when
Pin 21 is configured as the 12 V input. This bit reflects the logic
state of Pin 21 when the pin is configured as VID5.
VID CODE INPUT THRESHOLD VOLTAGE
The switching threshold for the VID code inputs is approximately
1 V. To enable future compatibility, it is possible to reduce the
VID code input threshold to 0.6 V. Bit 6 (THLD) of the VID
register (0x43) controls the VID input threshold voltage.
VID Code Register (0x43)
Bit 6 THLD = 0, VID switching threshold = 1 V,
VOL < 0.8 V, VIH > 1.7 V, VMAX = 3.3 V.
Bit 6 THLD = 1, VID switching threshold = 0.6 V,
VOL < 0.4 V, VIH > 0.8 V, VMAX = 3.3 V.
Bit 7 VIDSEL = 0, Pin 21 functions as a 12 V measurement
input. Software can read this bit to determine that there are five
VID inputs being monitored. Bit 5 of Register 0x43 (VID5)
always reads back 0. Bit 0 of Status Register 2 (0x42) reflects
12 V out-of-limit measurements.
Bit 7 VIDSEL = 1, Pin 21 functions as the sixth VID code input
(VID5). Software can read this bit to determine that there are
six VID inputs being monitored. Bit 5 of Register 0x43 reflects
the logic state of Pin 21. Bit 0 of Status Register 2 (0x42) reflects
VID code changes.
Reconfiguring Pin 21 as VID5 Input
Pin 21 can be reconfigured as a sixth VID code input (VID5)
for VRM10 compatible systems. Because the pin is configured
as VID5, it is not possible to monitor a 12 V supply.
Bit 7 of the VID configuration register (0x43) determines the
function of Pin 21. System or BIOS software can read the state
of Bit 7 to determine whether the system is designed to monitor
12 V or is monitoring a sixth VID input.
VID CODE CHANGE DETECT FUNCTION
The ADT7476 has a VID code change detect function. When
Pin 21 is configured as the VID5 input, VID code changes are
detected and reported back by the ADT7476. Bit 0 of Interrupt
Status Register 2 (0x42) is the 12 V/VC bit and denotes a VID
change when set. The VID code change bit is set when the logic
states on the VID inputs are different than they were 11 μs
previously. The change of VID code is used to generate an
SMBALERT interrupt. If an SMBALERT interrupt is not
required, Bit 0 of Interrupt Mask Register 2 (0x75), when set,
prevents SMBALERTs from occurring on VID code changes.
Interrupt Status Register 2 (0x42)
Bit 0 12 V/VC = 0, if Pin 21 is configured as VID5, Logic 0
denotes no change in VID code within the last 11 μs.
Bit 0 12 V/VC = 1, if Pin 21 is configured as VID5, Logic 1 means
that a change has occurred on the VID code inputs within the
last 11 μs. An SMBALERT is generated if this function is enabled.
PROGRAMMING THE GPIOS
The ADT7476 follows an upgrade path from the ADM1027 to
ADT7476. To maintain consistency between versions, it is
necessary to omit references to GPIO5. As a result, there are six
GPIOs as follows: GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, and
GPIO6.
Setting Bit 4 of Configuration Register 5 (0x7C) to 1 enables
GPIO functionality. This turns all pins configured as VID
inputs into general-purpose outputs. Writing to the corres-
ponding VID bit in the VID register (0x43) sets the polarity for
the corresponding GPIO. GPIO6 can be programmed indepen-
dently as an input/output using Bits [3:2] of Configuration
Register 5 (0x7C).
TEMPERATURE MEASUREMENT METHOD
Local Temperature Measurement
The ADT7476 contains an on-chip band gap temperature
sensor whose output is digitized by the on-chip, 10-bit ADC.
The 8-bit MSB temperature data is stored in the temperature
registers (Register 0x25, Register 0x26, and Register 0x27).
Because both positive and negative temperatures can be
measured, the temperature data is stored in Offset 64 format or
Theoretically, the temperature sensor and ADC can measure
temperatures from 63°C to +127°C (or 61°C to +191°C in
the extended temperature range) with a resolution of 0.25°C.
However, this exceeds the operating temperature range of the
device, so local temperature measurements outside the ADT7476
operating temperature range are not possible.
Remote Temperature Measurement
The ADT7476 can measure the temperature of two remote
diode sensors or diode-connected transistors connected to
Pin 17 and Pin 18 or to Pin 15 and Pin 16.
The forward voltage of a diode or diode-connected transistor
operated at a constant current exhibits a negative temperature
coefficient of about 2 mV/°C. Unfortunately, the absolute
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7482ARMZ-RL | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7482ARMZ-U2 | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7476EBZEVB | 功能描述:BOARD EVALUATION FOR ADT7476 RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:dBCool® 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADT7481 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm |
| ADT7481ARMZ | 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-001 | 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-1 | 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。