- 您现在的位置：买卖IC网 > PDF目录11209 > ADUC7022BCPZ32-RL (Analog Devices Inc)IC MCU 12BIT 1MSPS UART 40-LFCSP PDF资料下载
参数资料
| 型号： | ADUC7022BCPZ32-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 81/104页 |
| 文件大小： | 0K |
| 描述： | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| 标准包装： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 44MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | PLA，PWM，PSM，温度传感器，WDT |
| 输入/输出数： | 13 |
| 程序存储器容量： | 32KB（16K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 3.6 V |
| 数据转换器： | A/D 10x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页当前第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 78 of 104
Table 137. I2CxALT Registers
Name
Address
Default Value
Access
I2C0ALT
0xFFFF0828
0x00
R/W
I2C1ALT
0xFFFF0928
0x00
R/W
I2CxALT are hardware general call ID registers used in slave mode.
Table 138. I2CxCFG Registers
Name
Address
Default Value
Access
I2C0CFG
0xFFFF082C
0x00
R/W
I2C1CFG
0xFFFF092C
0x00
R/W
I2CxCFG are configuration registers.
Table 139. I2C0CFG MMR Bit Descriptions
Bit
Description
31:5
Reserved. These bits should be written by the user as 0.
14
Enable stop interrupt. Set by the user to generate an interrupt upon receiving a stop condition and after receiving a valid start
condition and matching address. Cleared by the user to disable the generation of an interrupt upon receiving a stop condition.
13
Reserved.
12
Reserved.
11
Enable stretch SCL (holds SCL low). Set by the user to stretch the SCL line. Cleared by the user to disable stretching of the SCL line.
10
Reserved.
9
Slave Tx FIFO request interrupt enable. Set by the user to disable the slave Tx FIFO request interrupt. Cleared by the user to generate
an interrupt request just after the negative edge of the clock for the R/W bit. This allows the user to input data into the slave Tx FIFO if
it is empty. At 400 ksps and the core clock running at 41.78 MHz, the user has 45 clock cycles to take appropriate action, taking
interrupt latency into account.
8
General call status bit clear. Set by the user to clear the general call status bits. Cleared automatically by hardware after the general
call status bits are cleared.
7
Master serial clock enable bit. Set by user to enable generation of the serial clock in master mode. Cleared by user to disable serial
clock in master mode.
6
Loopback enable bit. Set by user to internally connect the transition to the reception to test user software. Cleared by user to operate
in normal mode.
5
Start backoff disable bit. Set by user in multimaster mode. If losing arbitration, the master immediately tries to retransmit. Cleared by
user to enable start backoff. After losing arbitration, the master waits before trying to retransmit.
4
Hardware general call enable. When this bit and Bit 3 are set and have received a general call (Address 0x00) and a data byte, the
device checks the contents of I2C0ALT against the receive register. If the contents match, the device has received a hardware general
call. This is used if a device needs urgent attention from a master device without knowing which master it needs to turn to. This is a
“to whom it may concern” call. The ADuC7019/20/21/22/24/25/26/27/28/29 watch for these addresses. The device that requires
attention embeds its own address into the message. All masters listen, and the one that can handle the device contacts its slave and
acts appropriately. The LSB of the I2C0ALT register should always be written to 1, as indicated in The I2C-Bus Specification, January
2000, from NXP.
3
General call enable bit. This bit is set by the user to enable the slave device to acknowledge (ACK) an I2C general call, Address 0x00
(write). The device then recognizes a data bit. If it receives a 0x06 (reset and write programmable part of slave address by hardware)
as the data byte, the I2C interface resets as as indicated in The I2C-Bus Specification, January 2000, from NXP. This command can be
used to reset an entire I2C system. The general call interrupt status bit sets on any general call. The user must take corrective action by
setting up the I2C interface after a reset. If it receives a 0x04 (write programmable part of slave address by hardware) as the data byte,
the general call interrupt status bit sets on any general call. The user must take corrective action by reprogramming the device address.
2
Reserved.
1
Master enable bit. Set by user to enable the master I2C channel. Cleared by user to disable the master I2C channel.
0
Slave enable bit. Set by user to enable the slave I2C channel. A slave transfer sequence is monitored for the device address in I2C0ID0,
I2C0ID1, I2C0ID2, and I2C0ID3. At 400 kSPs, the core clock should run at 41.78 MHz because the interrupt latency could be up to 45
clock cycles alone. After the I2C read bit, the user has 0.5 of an I2C clock cycle to load the Tx FIFO. AT 400 kSPS, this is 1.26 μs, the
interrupt latency.
相关PDF资料 |
PDF描述 |
|---|---|
| AT90USB646-MUR | MCU AVR 64K FLASH 16MHZ 64QFN |
| AT90USB646-AUR | MCU AVR 64K FLASH 16MHZ 64TQFP |
| ADUC7023BCP6Z62IRL | IC MCU 12BIT 62KB FLASH 40LFCSP |
| ADUC7023BCPZ62I-RL | IC MCU 12BIT 62KB FLASH 32LFCSP |
| ATMEGA32L-8MUR | MCU AVR 32K FLASH 8MHZ 44QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7022BCPZ32-RL7 | 制造商:Analog Devices 功能描述:MCU 16-bit/32-bit ADuC7xxx ARM7TDMI RISC 32KB Flash 3.3V 40-Pin LFCSP EP T/R |
| ADUC7022BCPZ62 | 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
| ADUC7022BCPZ62-RL | 制造商:Analog Devices 功能描述:MCU 16-Bit/32-Bit ADuC7xxx ARM7TDMI RISC 62KB Flash 3.3V 40-Pin LFCSP EP T/R |
| ADUC7022BCPZ62-RL7 | 功能描述:IC MSU 12BIT 1MSPS UART 40-LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7023 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU with Enhanced IRQ Handler |
发布紧急采购，3分钟左右您将得到回复。