- 您现在的位置：买卖IC网 > PDF目录11204 > ADUC7036CCPZ-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LFCSP PDF资料下载
参数资料
| 型号： | ADUC7036CCPZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 75/132页 |
| 文件大小： | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LFCSP |
| 标准包装： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 9 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 115°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页当前第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页
ADuC7036
Rev. C | Page 47 of 132
ADC Interrupt Mask Register
Name: ADCMSKI
Address: 0xFFFF0504
Default Value: 0x00
Access: Read/write
Function: This register allows the ADC interrupt sources to be individually enabled. The bit positions in this register are the same as the
lower eight bits in the ADCSTA MMR. If a bit is set by user code to 1, the respective interrupt is enabled. By default, all bits are 0,
meaning all ADC interrupt sources are disabled.
ADC Mode Register
Name: ADCMDE
Address: 0xFFFF0508
Default Value: 0x00
Access: Read/write
Function: This 8-bit register configures the mode of operation of the ADC subsystem.
Table 36. ADCMDE MMR Bit Designations
Bit
Description
7
Not used. This bit is reserved for future functionality and should be written as 0 by user code.
6
20 kΩ resistor select.
Set to 1 to select the 20 kΩ resistor as shown in Figure 21.
Set to 0 to select the direct path to ground as shown in Figure 21 (default).
5
Low power mode reference select.
Set to 1 to enable the precision voltage reference in either low power mode or low power plus mode, thereby increasing current
consumption.
Set to 0 to enable the low power voltage reference in either low power mode or low power plus mode (default).
4 to 3
ADC power mode configuration.
00 = ADC normal mode. If enabled, the ADC operates with normal current consumption yielding optimum electrical performance.
01 = ADC low power mode. If enabled, the I-ADC operates with reduced current consumption. This limitation in current
consumption is achieved (at the expense of ADC noise performance) by fixing the gain to 128 and using the on-chip low power
(131 kHz) oscillator to directly drive the ADC circuits.
10 = ADC low power plus mode. If enabled, the ADC operates with reduced current consumption. In this mode, the gain is fixed to
512 and the current consumed is approximately 200 μA more than the ADC low power mode. The additional current consumed
also ensures that the ADC noise performance is better than that achieved in ADC low power mode.
11 = not defined.
2 to 0
ADC operation mode configuration.
000 = ADC power-down mode. All ADC circuits (including internal reference) are powered down.
001 = ADC continuous conversion mode. In this mode, any enabled ADC continuously converts.
010 = ADC single conversion mode. In this mode, any enabled ADC performs a single conversion. The ADC enters idle mode when
the single shot conversion is complete. A single conversion takes two to three ADC clock cycles depending on the chop mode.
011 = ADC idle mode. In this mode, the ADC is fully powered on but is held in reset.
100 = ADC self-offset calibration. In this mode, an offset calibration is performed on any enabled ADC using an internally
generated 0 V. The calibration is carried out at the user programmed ADC settings; therefore, as with a normal single ADC
conversion, it takes two to three ADC conversion cycles before a fully settled calibration result is ready. The calibration result is
automatically written to the ADCxOF MMR of the respective ADC. The ADC returns to idle mode and the calibration and
conversion ready status bits are set at the end of an offset calibration cycle.
101 = ADC self-gain calibration. In this mode, a gain calibration against an internal reference voltage is performed on all enabled
ADCs. A gain calibration is a two-stage process and takes twice the time of an offset calibration. The calibration result is
automatically written to the ADCxGN MMR of the respective ADC. The ADC returns to idle mode, and the calibration and
conversion ready status bits are set at the end of a gain calibration cycle. An ADC self-gain calibration should only be carried out
on the current channel ADC. Preprogrammed, factory calibration coefficients (downloaded automatically from internal Flash/EE)
should be used for voltage temperature measurements. If an external NTC is used, an ADC self-calibration should be performed
on the temperature channel.
110 = ADC system zero-scale calibration. In this mode, a zero-scale calibration is performed on enabled ADC channels against an
external zero-scale voltage driven at the ADC input pins. The calibration is carried out at the user programmed ADC settings;
therefore, as with a normal, single ADC conversion, it takes three ADC conversion cycles before a fully settled calibration result is ready.
111 = ADC system full-scale calibration. In this mode, a full-scale calibration is performed on enabled ADC channels against an
external full-scale voltage driven at the ADC input pins.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J30-IW-F2 | CONVERTER MOD DC/DC 5V 100W |
| ADUC7036DCPZ-RL | IC MCU 96K FLASH DUAL 48LFCSP |
| ADUC7036BCPZ-RL | IC SENSOR AUTO 96K FLASH 48LFCSP |
| ADUC7019BCPZ62IRL7 | IC MCU 12BIT 1MSPS I2C 40-LFCSP |
| AT91M42800A-33AU-999 | IC MCU 32BIT RISC 144LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7036DCPZ | 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7036DCPZ-RL | 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7038WBCPZ-RL | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 制造商:Analog Devices 功能描述:ARM Microcontrollers - MCU Flash 64k ARM7 Dual 16-Bit ADC LIN IC 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7039 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated, Precision Battery Sensor for Automotive Systems |
| ADUC7039BCP6Z | 功能描述:IC MCU ARM7 BATT SENSER 32LFCSP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
发布紧急采购，3分钟左右您将得到回复。