- 您现在的位置：买卖IC网 > PDF目录165355 > ADUC812BCPZ-REEL (ANALOG DEVICES INC) 8-BIT, FLASH, 11.0592 MHz, MICROCONTROLLER, PQCC56 PDF资料下载
参数资料
| 型号： | ADUC812BCPZ-REEL |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 11.0592 MHz, MICROCONTROLLER, PQCC56 |
| 封装： | LEAD FRAME, CSP-56 |
| 文件页数： | 58/60页 |
| 文件大小： | 1276K |
| 代理商： | ADUC812BCPZ-REEL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页
REV. E
ADuC812
–7–
PIN FUNCTION DESCRIPTIONS
Mnemonic
Type
Function
DVDD
PDigital Positive Supply Voltage, 3 V or 5 V Nominal.
AVDD
PAnalog Positive Supply Voltage, 3 V or 5 V Nominal.
CREF
IDecoupling Input for On-Chip Reference. Connect 0.1 F between this pin and AGND.
VREF
I/O
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the
reference source for the ADC. The nominal internal reference voltage is 2.5 V, which appears at the pin.
This pin can be overdriven by an external reference.
AGND
G
Analog Ground. Ground reference point for the analog circuitry.
P1.0–P1.7
I
Port 1 is an 8-bit input port only. Unlike other ports, Port 1 defaults to Analog Input mode. To configure
any of these Port Pins as a digital input, write a 0 to the port bit. Port 1 pins are multifunctional and share
the following functionality.
ADC0–ADC7
I
Analog Inputs. Eight single-ended analog inputs. Channel selection is via ADCCON2 SFR.
T2
I
Timer 2 Digital Input. Input to Timer/Counter 2. When enabled, Counter 2 is incremented in response to a
1 to 0 transition of the T2 input.
T2EX
I
Digital Input. Capture/Reload trigger for Counter 2; also functions as an Up/Down control input for
Counter 2.
SS
I
Slave Select Input for the SPI Interface.
SDATA
I/O
User selectable, I
2C Compatible or SPI Data Input/Output Pin.
SCLOCK
I/O
Serial Clock Pin for I
2C Compatible or SPI Serial Interface Clock.
MOSI
I/O
SPI Master Output/Slave Input Data I/O Pin for SPI Interface.
MISO
I/O
SPI Master Input/Slave Output Data I/O Pin for SPI Serial Interface.
DAC0
O
Voltage Output from DAC0.
DAC1
O
Voltage Output from DAC1.
RESET
I
Digital Input. A high level on this pin for 24 master clock cycles while the oscillator is running resets the
device. External power-on reset (POR) circuity must be implemented to drive the RESET pin as described
in the Power-On Reset Operation section.
P3.0–P3.7
I/O
Port 3 is a bidirectional port with internal pull-up resistors. Port 3 pins that have 1s written to them are
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal pull-up resistors. Port 3 pins also
contain various secondary functions that are described below.
RxD
I/O
Receiver Data Input (Asynchronous) or Data Input/Output (Synchronous) of Serial (UART) Port
TxD
O
Transmitter Data Output (Asynchronous) or Clock Output (Synchronous) of Serial (UART) Port
INT0
I
Interrupt 0, programmable edge or level triggered Interrupt input,
INT0 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 0.
INT1
I
Interrupt 1, programmable edge or level triggered Interrupt input,
INT1 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 1.
T0
I
Timer/Counter 0 Input.
T1
I
Timer/Counter 1 Input.
CONVST
I
Active Low Convert Start Logic Input for the ADC Block when the External Convert Start Function is Enabled.
A low-to-high transition on this input puts the track-and-hold into its hold mode and starts conversion.
WR
OWrite Control Signal, Logic Output. Latches the data byte from Port 0 into the external data memory.
RD
ORead Control Signal, Logic Output. Enables the external data memory to Port 0.
XTAL2
O
Output of the Inverting Oscillator Amplifier.
XTAL1
I
Input to the Inverting Oscillator Amplifier and to the Internal Clock Generator Circuits.
DGND
G
Digital Ground. Ground reference point for the digital circuitry.
P2.0–P2.7
I/O
Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s written to them are
(A8–A15)
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 2
(A16–A23)
pins being pulled externally low will source current because of the internal pull-up resistors. Port 2 emits the
high order address bytes during fetches from external program memory and middle and high order address
bytes during accesses to the external 24-bit external data memory space.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM1510BRWZ | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| ADUM3210ARZ-RL7 | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| AE101SD1AB | TOGGLE SWITCH, SPDT, LATCHED, 0.02A, 20VDC, THROUGH HOLE-RIGHT ANGLE |
| AE103MD1CB | TOGGLE SWITCH, SPDT, MOMENTARY, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| AE235RAA2N0JSW | 1 ELEMENT, 0.002 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC812BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 16MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC MQFP52 812 制造商:Analog Devices 功能描述:Data Acquisition System, 8 Channel, 12 Bit, 52 Pin, Plastic, QFP |
| ADUC812BS | 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED |
| aduc812bs-01 | 制造商:Analog Devices 功能描述: |
| ADUC812BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R |
| ADUC812BSZ | 功能描述:IC ADC 12BIT MULTICH MCU 52-MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
发布紧急采购，3分钟左右您将得到回复。