- 您现在的位置：买卖IC网 > PDF目录11206 > ADUC814BRUZ-REEL7 (Analog Devices Inc)IC MCU 8K FLASH ADC/DAC 28-TSSOP PDF资料下载
参数资料
| 型号： | ADUC814BRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/72页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8K FLASH ADC/DAC 28-TSSOP |
| 标准包装： | 1,000 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 16.78MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，温度传感器，WDT |
| 输入/输出数： | 17 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 6x12b; D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
| 配用： | EVAL-ADUC814QSZ-ND - KIT DEV FOR ADUC814 MICROCONVRTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
ADuC814
Rev. A | Page 27 of 72
Both the ADCCLK frequency and the acquisition time are used
in determining the ADC conversion time. Two other parameters
are also used in this calculation. To convert the acquired signal
into its corresponding digital output word takes 15 ADCCLK
periods (TCONV). When a conversion is initiated, the start of
conversion signal is synchronized to the ADCCLK. This synchro-
nization (TSYNC) can take from 0.5 to 1.5 ADCCLKs to occur.
The total ADC conversion time TADC is calculated using the
following formula:
TADC = TSYNC + TACQ + TCONV
Assuming TSYNC = 1, TACQ = 1 and FCORE/ADCCLK divider of 4.
The total conversion time is calculated by
TADC = (1 + 1 + 15) × (1 / 4194304)
TADC = 4.05 s
These settings allow a maximum conversion speed or sampling
rate of 246.7 kHz.
When converting on the temperature monitor channel, the
conversion time is not controlled via the ADCCON registers. It
is controlled in hardware and sets the ADCCLK to FCORE /32
and uses four acquisition clocks, giving a total ADC conversion
time of
TADC = (1 + 4 + 15) × (1 / 524288) = 38.14 s
Increasing the conversion time on the temperature monitor
channel improves the accuracy of the reading. To further
improve the accuracy, an external reference with low tempera-
ture drift should also be used.
INITIATING ADC CONVERSIONS
After the ADC has been turned on and configured, there are
four methods of initiating ADC conversions.
Single conversions can be initiated in software by setting the
SCONV bit in the ADCCON2 register via user code. This
causes the ADC to perform a single conversion and puts the
result into the ADCDATAH/L SFRs. The SCONV bit is cleared
as soon as the ADCDATA SFRs have been updated.
Continuous conversion mode can be initiated by setting the
CCONV bit in ADCCON2 via user code. This performs back-
to-back conversions at the configured rate (246.7 kHz for the
settings detailed previously). In continuous mode, the ADC
results must be read from the ADCDATA SFRs before the next
conversion is completed to avoid loss of data. Continuous mode
can be stopped by clearing the CCONV bit.
An external signal can also be used to initiate ADC conversions.
Setting Bit 0 in ADCCON1 enables the logic to allow an
external start-of-conversion signal on Pin 7 (CONVST). This
active low pulse should be at least 100 ns wide. The rising edge
of this signal initiates the conversion.
Timer 2 can also be used to initiate conversions. Setting Bit 1
of ADCCON1 enables the Timer 2 overflow signal to start a
conversion. For Timer 2 configuration information, see the
Timers/Counters section.
For both external CONVST and Timer 2 overflow, the conver-
sion rate must be equal to or greater than the conversion time
(TADC) to avoid incorrect ADC results.
When initiating conversions, the user must ensure that only one
of the trigger modes is active at any one time. Initiating conver-
sions with more than one of the trigger modes active results in
erratic ADC behavior.
ADC HIGH SPEED DATA CAPTURE MODE
The on-chip ADC has been designed to run at a maximum
conversion speed of 4.05 s (247 kHz sampling rate). When
converting at this rate, the ADuC814 MCU has 4.05 s to read
the ADC result and store it in memory for further post
processing; otherwise the next ADC sample could be lost. The
time to complete a conversion and store the ADC results
without errors is known as the throughput rate. In an interrupt
driven routine, the MCU also has to jump to the ADC interrupt
service routine, which decreases the throughput rate of the
ADuC814. In applications where the ADuC814 standard
operating mode throughput is not fast enough, an ADC high
speed data capture (HSDC) mode is provided.
In HSDC mode, ADC results are transferred to the SPI logic
without intervention from the ADuC814 core logic. In applica-
tions where the ADC throughput is slow, the HSDC logic operates
in non-pipelined mode (Figure 29). In this mode, there is
adequate time for the ADC conversion and the ADC-to-SPI
data transfer to complete before the next start of conversion. As
the ADC throughput increases, the HSDC logic begins to operate
in pipelined mode as shown in Figure 30.
ADCDATAH
ADCDATAL
MOSI
SCLOCK
BUSY
CONVST
02748-A
-036
Figure 29. High Speed Data Capture Logic Timing (Non-Pipelined Mode)
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC814BRUZ-REEL | IC MCU 8K FLASH ADC/DAC 28-TSSOP |
| ADUC7025BCPZ32-RL | IC MCU 12BIT 1MSPS UART 64-LFCSP |
| ADUC7021BCPZ32-RL7 | IC MCU FLASH 32K W/ANLG 40LFCSP |
| AT90CAN128-16AUR | IC MCU AVR 128K FLASH 64TQFP |
| AT90CAN128-16MUR | IC MCU AVR 128K FLASH 64QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC816 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ADuC816: MicroConverter?= Dual 16-Bit ADC + 12-Bit DAC + Flash MCU Data Sheet (Rev. 0. 2/01 |
| ADUC816ASZ | 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 12.58MHz 8KB (8K x 8) FLASH 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包装:- 零件状态:上次购买时间 核心处理器:8052 核心尺寸:8-位 速度:12.58MHz 连接性:I2C，SPI，UART/USART 外设:PSM，温度传感器，WDT I/O 数:34 程序存储容量:8KB（8K x 8） 程序存储器类型:闪存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 7x16b；D/A 1x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:- 供应商器件封装:- 标准包装:1 |
| ADUC816BCP | 功能描述:IC MCU 8K FLASH ADC/DAC 56LFCSP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC816BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:MCU 8BIT CISC 8KB FLASH 3.3V/5V 56LFCSP EP - Tape and Reel |
| ADUC816BCPZ | 功能描述:IC MCU FLASH 16BIT ADC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。