- 您现在的位置：买卖IC网 > Datasheet目录308 > ADUM3442CRWZ-RL (Analog Devices Inc)IC DIGITAL ISOLATOR 4CHAN 16SOIC Datasheet资料下载
参数资料
| 型号： | ADUM3442CRWZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | IC DIGITAL ISOLATOR 4CHAN 16SOIC |
| 标准包装： | 1,000 |
| 系列： | iCoupler® |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 4 |
| 电源电压： | 3 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 150Mbps |
| 传输延迟： | 36ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
ADuM3440/ADuM3441/ADuM3442
APPLICATIONS INFORMATION
PC BOARD LAYOUT
The ADuM344x digital isolator requires no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins (see
Figure 16). Bypass capacitors are most conveniently connected
between Pin 1 and Pin 2 for V DD1 and between Pin 15 and Pin 16
for V DD2 . The capacitor value should be between 0.01 μF and 0.1 μF.
Data Sheet
SYSTEM-LEVEL ESD CONSIDERATIONS AND
ENHANCEMENTS
System-level ESD reliability (for example, per IEC 61000-4-x)
is highly dependent on system design, which varies widely by
application. The ADuM344x incorporate many enhancements
to make ESD reliability less dependent on system design. The
enhancements include the following:
The total lead length between both ends of the capacitor and
the input power supply pin should not exceed 20 mm. Bypassing
between Pin 1 and Pin 8 and between Pin 9 and Pin 16 should
be considered unless the ground pair on each package side is
connected close to the package.
?
?
?
ESD protection cells added to all input/output interfaces.
Key metal trace resistances reduced using wider geometry
and paralleling of lines with vias.
The SCR effect inherent in CMOS devices is minimized by
V DD1
V DD2
the use of guarding and isolation techniques between
GND 1
V IA
V IB
V IC/OC
V ID/OD
V E1
GND 1
GND 2
V OA
V OB
V OC/IC
V OD/ID
V E2
GND 2
?
?
PMOS and NMOS devices.
Areas of high electric field concentration eliminated using
45° corners on metal traces.
Supply pin overvoltage prevented with larger ESD clamps
Figure 16. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, care
should be taken to ensure that board coupling across the isolation
barrier is minimized. Furthermore, the board layout should be
designed such that any coupling that does occur equally affects
all pins on a given component side. Failure to ensure this could
cause voltage differentials between pins exceeding the device’s
absolute maximum ratings, thereby leading to latch-up or
permanent damage.
See the AN-1109 Application Note for board layout guidelines.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The propagation
delay to a logic low output may differ from the propagation
delay to a logic high.
between each supply pin and its respective ground.
While the ADuM344x improve system-level ESD reliability,
they are no substitute for a robust system-level design. See the
AN-793 application note, ESD/Latch-Up Considerations with
iCoupler Isolation Products for detailed recommendations on
board layout and system-level design.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder via the transformer.
The decoder is bistable and is, therefore, either set or reset by
the pulses, indicating input logic transitions. In the absence of
logic transitions at the input for more than ~1 μs, a periodic set
of refresh pulses indicative of the correct input state are sent to
ensure dc correctness at the output. If the decoder receives no
internal pulses of more than about 5 μs, the input side is assumed
unpowered or nonfunctional, in which case the isolator output
INPUT (V Ix )
OUTPUT (V Ox )
t PLH
t PHL
50%
50%
is forced to a default state (see the Absolute Maximum Ratings
section) by the watchdog timer circuit.
The limitation on the magnetic field immunity of the ADuM344x
is set by the condition in which induced voltage in the receiving
Figure 17. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM344x component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM344x
coil of the transformer is sufficiently large to either falsely set or
reset the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of the
ADuM344x is examined because it represents the most susceptible
mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V,
thus establishing a 0.5 V margin in which induced voltages can
be tolerated.
components operating under the same conditions.
Rev. D | Page 18 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM4223BRWZ | ISOLATOR DIGITAL |
| ADUM4402CRWZ | IC DIGITAL ISOLATOR 4CH 16-SOIC |
| ADUM5000ARWZ-RL | IC DIG ISOLATOR W/DC-DC 16SOIC |
| ADUM5201CRWZ | IC DGTL ISOLATOR W/DC-DC 16SOIC |
| ADUM5230ARWZ-RL | IC ISOLATOR 2CH HBRIDGE 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM344X | 制造商:AD 制造商全称:Analog Devices 功能描述:Digital Isolator Product Selection and Resource Guide |
| ADUM3470 | 制造商:AD 制造商全称:Analog Devices 功能描述:PWM Controller and Transformer Driver with Quad-Channel Isolators |
| ADUM3470ARSZ | 功能描述:隔离器接口集成电路 4-Ch Isolators w/ Int Transformer Driver RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| ADUM3470ARSZ-RL7 | 功能描述:隔离器接口集成电路 4-Ch Isolators w/ Int Transformer Driver RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| ADUM3470CRSZ | 功能描述:ISOLAT DGTL 2.5KVRMS 4CH 20SSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
发布紧急采购，3分钟左右您将得到回复。