- 您现在的位置：买卖IC网 > Datasheet目录308 > ADUM3442CRWZ-RL (Analog Devices Inc)IC DIGITAL ISOLATOR 4CHAN 16SOIC Datasheet资料下载
参数资料
| 型号： | ADUM3442CRWZ-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC DIGITAL ISOLATOR 4CHAN 16SOIC |
| 标准包装： | 1,000 |
| 系列： | iCoupler® |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 4 |
| 电源电压： | 3 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 150Mbps |
| 传输延迟： | 36ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 105°C |
Data Sheet
The voltage induced across the receiving coil is given by
1000
ADuM3440/ADuM3441/ADuM3442
V = ( ?d β /dt )∑ π r ; n = 1, 2, … , N
2
n
where:
β is magnetic flux density (gauss).
N is the number of turns in the receiving coil.
r n is the radius of the n th turn in the receiving coil (cm).
100
10
DISTANCE = 100mm
DISTANCE = 1m
Given the geometry of the receiving coil in the ADuM344x and
an imposed requirement that the induced voltage be at most
50% of the 0.5 V margin at the decoder, a maximum allowable
magnetic field is calculated as shown in Figure 18.
100
1
0.1
0.01
DISTANCE = 5mm
1k
10k
100k
1M
10M
100M
MAGNETIC FIELD FREQUENCY (Hz)
I DDO = ( I DDO ( D ) + (0.5 × 10 ) × C L × V DDO ) × (2 f ? f r ) + I DDO ( Q )
10
1
0.1
0.01
0.001
1k 10k 100k 1M 10M 100M
MAGNETIC FIELD FREQUENCY (Hz)
Figure 18. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.2 kgauss induces a
voltage of 0.25 V at the receiving coil. This is about 50% of the
sensing threshold and does not cause a faulty output transition.
Similarly, if such an event were to occur during a transmitted
pulse (and was of the worst-case polarity), it would reduce the
received pulse from >1.0 V to 0.75 V—still well above the 0.5 V
sensing threshold of the decoder.
The preceding magnetic flux density values correspond to
specific current magnitudes at given distances from the
ADuM344x transformers. Figure 19 expresses these allowable
current magnitudes as a function of frequency for selected
distances. As shown, the ADuM344x is extremely immune
and can be affected only by extremely large currents operated
at high frequency very close to the component. For the 1 MHz
example noted, one would have to place a 0.5 kA current 5 mm
away from the ADuM344x to affect the component’s operation.
Figure 19. Maximum Allowable Current
for Various Current-to-ADuM344x Spacings
Note that at combinations of strong magnetic field and high
frequency, any loops formed by printed circuit board traces
could induce error voltages sufficiently large enough to trigger
the thresholds of succeeding circuitry. Care should be taken in
the layout of such traces to avoid this possibility.
POWER CONSUMPTION
The supply current at a given channel of the ADuM344x
isolator is a function of the supply voltage, the channel’s data
rate, and the channel’s output load.
For each input channel, the supply current is given by
I DDI = I DDI ( Q ) f ≤ 0.5 f r
I DDI = I DDI (D) × (2 f ? f r ) + I DDI ( Q ) f > 0.5 f r
For each output channel, the supply current is given by
I DDO = I DDO ( Q ) f ≤ 0.5 f r
?3
f > 0.5 f r
where:
I DDI (D) , I DDO (D) are the input and output dynamic supply currents
per channel (mA/Mbps).
C L is the output load capacitance (pF).
V DDO is the output supply voltage (V).
f is the input logic signal frequency (MHz); it is half of the input
data rate expressed in units of Mbps.
f r is the input stage refresh rate (Mbps).
I DDI (Q) , I DDO (Q) are the specified input and output quiescent
supply currents (mA).
To calculate the total V DD1 and V DD2 supply current, the supply
currents for each input and output channel corresponding to
V DD1 and V DD2 are calculated and totaled. Figure 8 and Figure 9
provide per-channel supply currents as a function of data rate
for an unloaded output condition. Figure 10 provides per-
channel supply current as a function of data rate for a 15 pF
output condition. Figure 11 through Figure 15 provide total
V DD1 and V DD2 supply current as a function of data rate for
ADuM3440/ADuM3441/ADuM3442 channel configurations.
Rev. D | Page 19 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM4223BRWZ | ISOLATOR DIGITAL |
| ADUM4402CRWZ | IC DIGITAL ISOLATOR 4CH 16-SOIC |
| ADUM5000ARWZ-RL | IC DIG ISOLATOR W/DC-DC 16SOIC |
| ADUM5201CRWZ | IC DGTL ISOLATOR W/DC-DC 16SOIC |
| ADUM5230ARWZ-RL | IC ISOLATOR 2CH HBRIDGE 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM344X | 制造商:AD 制造商全称:Analog Devices 功能描述:Digital Isolator Product Selection and Resource Guide |
| ADUM3470 | 制造商:AD 制造商全称:Analog Devices 功能描述:PWM Controller and Transformer Driver with Quad-Channel Isolators |
| ADUM3470ARSZ | 功能描述:隔离器接口集成电路 4-Ch Isolators w/ Int Transformer Driver RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| ADUM3470ARSZ-RL7 | 功能描述:隔离器接口集成电路 4-Ch Isolators w/ Int Transformer Driver RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| ADUM3470CRSZ | 功能描述:ISOLAT DGTL 2.5KVRMS 4CH 20SSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:iCoupler® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
发布紧急采购，3分钟左右您将得到回复。