- 您现在的位置：买卖IC网 > PDF目录21463 > ADUM6132ARWZ (Analog Devices Inc)IC GATE DVR ISO HALF BRDG 16SOIC PDF资料下载
参数资料
| 型号： | ADUM6132ARWZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC GATE DVR ISO HALF BRDG 16SOIC |
| 其它图纸： | ADUM6132 Block Diagram |
| 标准包装： | 47 |
| 系列： | isoPower® |
| 输入 - 1 侧/2 侧： | 2/0 |
| 通道数： | 2 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电压 - 隔离： | 3750Vrms |
| 传输延迟： | 60ns |
| 输出类型： | 逻辑 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 2766 (CN2011-ZH PDF) |
ADuM6132
In applications involving high common-mode transients, care
should be taken to ensure that board capacitive coupling across
the isolation barrier is minimized. Furthermore, the board
layout should be designed so that any coupling that does occur
affects all pins on a given component side equally. Failure to
ensure this may cause voltage differentials between pins that
exceed the absolute maximum ratings of the device (see Table 7),
leading to latch-up or permanent damage.
V DD V ISO
GND GND ISO
Data Sheet
UNDERVOLTAGE LOCKOUT
The ADuM6132 has undervoltage lockout (UVLO) circuits on
the V DDL , V DDA , and V DDB supplies. For each supply, the respective
UVLO circuit monitors the supply voltage and takes a predeter-
mined action based on whether the supply voltage is above or
below a given threshold. These thresholds are specified in Table 1.
In the recommended configuration shown in Figure 16, only
two independent supplies are controlled by the user: V DDB and
V DDL /V DD (V DDL = V DD in Figure 16). V DDA is supplied by the
V DDL
V IA
V IB
V OB
V DDB
GND
Figure 17. Recommended PCB Layout
GND A
V DDA
V OA
NC
NC
GND ISO
internal dc-to-dc converter via the V ISO = V DDA external connec-
tion. Nevertheless, the V DDA UVLO functionality is included in
Table 11 to show how the V OA output behaves when the internal
dc-to-dc converter powers on and off.
Table 11. Undervoltage Lockout Functionality 1
The ADuM6132 is a power device that dissipates approximately
1 W of power when fully loaded and running at maximum speed.
Because it is not possible to apply a heat sink to an isolation
device, the device depends primarily on heat dissipation into
the PCB through the GND pins. If the device will be used at
high ambient temperatures, provide a thermal path from the
GND pins to the PCB ground plane.
The board layout in Figure 17 shows enlarged pads for Pin 8
(GND) and Pin 9 (GND ISO ). Multiple vias should be implemented
from the pad to the ground plane. This layout significantly reduces
the temperatures inside the chip. The dimensions of the expanded
pads are left to the discretion of the designer and the available
board space. See the AN-0971 Application Note for board
layout recommendations.
User-Provided
Supplies
V DDL V DDB
H H
H H
X L
V ISO Powered
Supply
V DDA
H
L
X
Effect
Normal operation.
Internal dc-to-dc converter is
active.
V OA /V OB output logic states
match V IA /V IB input logic states.
Internal dc-to-dc converter is
active but V ISO is below UVLO
threshold.
V OA output is driven low.
V OB output operates normally.
Internal dc-to-dc converter is
turned off (V ISO = 0 V).
V OA output is driven low.
V OB output is driven low.
THERMAL ANALYSIS
L
X
X
Internal dc-to-dc converter is
turned off (V ISO = 0 V).
The ADuM6132 consists of several internal die attached to
two lead frame paddles. For the purposes of thermal analysis,
V OA output is driven low.
V OB output is driven low.
the part is treated as a thermal unit with the highest junction
temperature determining θ JA , as shown in Table 2. The value of
1
H: supply voltage > UVLO threshold; L: supply voltage < UVLO threshold;
X: supply voltage level is irrelevant.
θ JA is based on measurements taken with the part mounted on
a JEDEC standard 4-layer board with fine width traces and still
air. Under normal operating conditions, the ADuM6132 oper-
ates at full load across the full temperature range without derating
the output current. However, following the recommendations in
the PCB Layout section decreases the thermal resistance to the
PCB, allowing increased thermal margin at high ambient
temperatures.
Under V ISO output short-circuit conditions, as shown in
Figure 9, the package power dissipation quickly exceeds the safe
operating limit of 1.44 W for ambient temperatures up to 85°C.
At low input voltage, the power dissipation can approach 2 W.
Because internal compensation of the PWM makes low V DD a
worst-case condition, input voltage limiting is not an effective
strategy for protecting the ADuM6132 from output load fault
conditions. Therefore, the preferred protection methods, where
When all three supplies are above their respective UVLO
thresholds, the ADuM6132 operates normally. The internal
dc-to-dc converter is active, and both outputs operate as
determined by their respective input logic signals. If either of
the user-provided supplies is below its UVLO threshold, the
ADuM6132 is put into a disabled mode. In this mode, the
internal dc-to-dc converter is turned off and both outputs are
driven low.
The V OB output is driven low by either the V DDL or V DDB
UVLO circuit (whichever is below its threshold). The V OA
output is driven low when the internal dc-to-dc converter is
turned off. The V ISO supply voltage drops to 0 V, causing V DDA
to drop also because V ISO and V DDA are externally connected.
When V DDA is below its UVLO threshold, the V DDA UVLO
circuit drives V OA low.
required, are either limiting ambient temperature to 60°C or the
use of a fuse.
Rev. B | Page 12 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| 3112KL-05W-B60-E00 | FAN DC AXIAL 24V 80X32 4350 RPM |
| C-1557 | CABINET SLOPING PANEL PRESTIGE |
| ADUM1402CRWZ-RL | IC DGITAL ISOLATOR 4CH 16-SOIC |
| DK1A-L2-5V | RELAY GEN PURPOSE SPST 10A 5V |
| DK1A-L2-24V | RELAY GEN PURPOSE SPST 10A 24V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUM6132ARWZ-RL | 功能描述:IC GATE DRIVER ISOLATED 16-SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:isoPower® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM6200 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual-Channel, 5 kV Isolators with Integrated DC-to-DC Converter |
| ADUM6200ARIZ | 功能描述:IC ISOLATOR DGTL 2CH 16SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoPower®, iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM6200ARIZ-RL | 功能描述:IC ISOLATOR DGTL 2CH 16SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoPower®, iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| ADUM6200ARWZ | 功能描述:ISOLAT DGTL 5KVRMS 2CH 16SOIC-W RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoPower®, iCoupler® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
发布紧急采购，3分钟左右您将得到回复。