参数资料
| 型号： | ADV7189BBSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 41/104页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO DECODER SDTV 80-LQFP |
| 标准包装： | 1 |
| 类型： | 视频解码器 |
| 应用： | 机顶盒，视频播放器，录音机 |
| 电压 - 电源，模拟： | 3.15 V ~ 3.45 V |
| 电压 - 电源，数字： | 1.65 V ~ 2 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 80-LQFP |
| 供应商设备封装： | 80-LQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
ADV7189B
Rev. B | Page 41 of 104
VS and FIELD Configuration
The following controls allow the user to configure the behav-
ior of the VS and FIELD output pins, as well as to generate
embedded AV codes:
ADV encoder-compatible signals via NEWAVMODE
PVS, PF
HVSTIM
VSBHO, VSBHE
VSEHO, VSEHE
For NTSC control:
NVBEGDELO, NVBEGDELE, NVBEGSIGN,
NVBEG[4:0]
NVENDDELO, NVENDDELE, NVENDSIGN,
NVEND[4:0]
NFTOGDELO, NFTOGDELE, NFTOGSIGN,
NFTOG[4:0]
For PAL control:
PVBEGDELO, PVBEGDELE, PVBEGSIGN,
PVBEG[4:0]
PVENDDELO, PVENDDELE, PVENDSIGN,
PVEND[4:0]
PFTOGDELO, PFTOGDELE, PFTOGSIGN,
PFTOG[4:0]
NEWAVMODE New AV Mode, Address 0x31[4]
When NEWAVMODE is 0, EAV/SAV codes are generated to
suit ADI encoders. No adjustments are possible.
Setting NEWAVMODE to 1 (default) enables the manual
position of the VSYNC, Field, and AV codes using
Registers 0x34 to 0x37 and Register 0xE5 to 0xEA. Default
register settings are CCIR656 compliant; see
207H
Figure 21 for NTSC
and
208H
Figure 26 for PAL. For recommended manual user settings,
see
209H
Table 56 and
210H
Figure 22 for NTSC; see
211H
Table 57 and
212H
Figure 27
for PAL.
HVSTIM Horizontal VS Timing, Address 0x31[3]
The HVSTIM bit allows the user to select where the VS signal
is being asserted within a line of video. Some interface circuitry
can require VS to go low while HS is low.
When HVSTIM is 0 (default) the start of the line is relative
to HSE.
When HVSTIM is 1, the start of the line is relative to HSB.
VSBHO VS Begin Horizontal Position Odd, Address 0x32[7]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHO is 0 (default), the VS pin goes high at the middle
of a line of video (odd field).
When VSBHO is 1, the VS pin changes state at the start of a line
(odd field).
VSBHE VS Begin Horizontal Position Even, Address 0x32[6]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHE is 0 (default), the VS pin goes high at the middle
of a line of video (even field).
When VSBHE is 1, the VS pin changes state at the start of a line
(even field).
VSEHO VS End Horizontal Position Odd, Address 0x33{7]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHO is 0, the VS pin goes low (inactive) at the middle
of a line of video (odd field).
When VSEHO is 1 (default), the VS pin changes state at the
start of a line (odd field).
VSEHE VS End Horizontal Position Even, Address 0x33[6]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHE is 0 (default), the VS pin goes low (inactive) at
the middle of a line of video (even field).
When VSEHE is 1, the VS pin changes state at the start of a line
(even field).
PVS Polarity VS, Address 0x37[5]
The polarity of the VS pin can be inverted using the PVS bit.
When PVS is 0 (default), VS is active high. When PVS is 1, VS is
active low.
PF Polarity FIELD, Address 0x37[3]
The polarity of the FIELD pin can be inverted using the PF bit.
When PF is 0 (default), FIELD is active high. When PF is 1,
FIELD is active low.
相关PDF资料 |
PDF描述 |
|---|---|
| ADV7194KSTZ | IC ENCODER VIDEO EXT-10 80-LQFP |
| ADV7202KSTZ | IC CODEC VIDEO 10BIT 64LQFP |
| ADV7311KST | IC VID ENC 6-12BIT DAC'S 64LQFP |
| ADV7321KSTZ | IC VID ENC 6-12BIT DAC'S 64LQFP |
| ADV7343BSTZ | IC ENCODER VIDEO W/DAC 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADV7189BBSTZ268H | 制造商:AD 制造商全称:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BBSTZ268H2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
| ADV7189BKST | 制造商:Analog Devices 功能描述: |
| ADV7189BKSTZ | 功能描述:IC DECODER VIDEO W/ADC 80LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 编码器，解码器，转换器 系列:- 产品变化通告:Development Systems Discontinuation 26/Apr/2011 标准包装:1 系列:- 类型:编码器 应用:DVB-S.2 系统 电压 - 电源，模拟:- 电压 - 电源，数字:- 安装类型:- 封装/外壳:模块 供应商设备封装:模块 包装:散装 其它名称:Q4645799 |
| ADV7189BKSTZ10F | 制造商:AD 制造商全称:Analog Devices 功能描述:Multiformat SDTV Video Decoder |
发布紧急采购，3分钟左右您将得到回复。