- 您现在的位置：买卖IC网 > PDF目录17055 > AGLN-NANO-KIT (Microsemi SoC)KIT HARDWARE FOR AGLN-NANO PDF资料下载
参数资料
| 型号： | AGLN-NANO-KIT |
| 厂商： | Microsemi SoC |
| 文件页数： | 9/150页 |
| 文件大小： | 0K |
| 描述： | KIT HARDWARE FOR AGLN-NANO |
| 标准包装： | 1 |
| 系列： | IGLOO nano |
| 类型： | FPGA |
| 适用于相关产品： | AGLN250 |
| 所含物品： | 板，电缆，DVD，跳线，编程器 |
| 其它名称： | 1100-1136 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页
Pin Descriptions
3-2
Revision 17
interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be powered for JTAG operation; VJTAG alone is
insufficient. If a device is in a JTAG chain of interconnected boards, the board containing the device can
be powered down, provided both VJTAG and VCC to the part remain powered; otherwise, JTAG signals
will not be able to transition the device, even in bypass mode.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
IGLOO nano devices support single-voltage ISP of the configuration flash and FlashROM. For
programming, VPUMP should be 3.3 V nominal. During normal device operation, VPUMP can be left
floating or can be tied (pulled up) to any voltage between 0 V and the VPUMP maximum. Programming
power supply voltage (VPUMP) range is listed in the datasheet.
When the VPUMP pin is tied to ground, it will shut off the charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 F and 0.33 F capacitors (both rated at 16 V) are to be connected in
parallel across VPUMP and GND, and positioned as close to the FPGA pins as possible.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
User Pins
I/O
User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected.
During programming, I/Os become tristated and weakly pulled up to VCCI. With VCCI, VMV, and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os are instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high impedance)
Input buffer is disabled (with tristate value of high impedance)
Weak pull-up is programmed
GL
Globals
GL I/Os have access to certain clock conditioning circuitry (and the PLL) and/or have direct access to the
global network (spines). Additionally, the global I/Os can be used as regular I/Os, since they have
identical capabilities. Unused GL pins are configured as inputs with pull-up resistors.
See more detailed descriptions of global I/O connectivity in the "Clock Conditioning Circuits in IGLOO
and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide. All inputs labeled
GC/GF are direct inputs into the quadrant clocks. For example, if GAA0 is used for an input, GAA1 and
GAA2 are no longer available for input to the quadrant globals. All inputs labeled GC/GF are direct inputs
into the chip-level globals, and the rest are connected to the quadrant globals. The inputs to the global
network are multiplexed, and only one input can be used as a global input.
Refer to the "I/O Structures in nano Devices" chapter of the IGLOO nano FPGA Fabric User’s Guide for
an explanation of the naming of global pins.
FF
Flash*Freeze Mode Activation Pin
Flash*Freeze is available on IGLOO nano devices. The FF pin is a dedicated input pin used to enter and
exit Flash*Freeze mode. The FF pin is active low, has the same characteristics as a single-ended I/O,
and must meet the maximum rise and fall times. When Flash*Freeze mode is not used in the design, the
FF pin is available as a regular I/O.
When Flash*Freeze mode is used, the FF pin must not be left floating to avoid accidentally entering
Flash*Freeze mode. While in Flash*Freeze mode, the Flash*Freeze pin should be constantly asserted.
The Flash*Freeze pin can be used with any single-ended I/O standard supported by the I/O bank in
which the pin is located, and input signal levels compatible with the I/O standard selected. The FF pin
相关PDF资料 |
PDF描述 |
|---|---|
| GEC28DRAI | CONN EDGECARD 56POS R/A .100 SLD |
| HK100515NJ-T | INDUCTOR HI FREQ 15NH 5% 0402 |
| 0210390908 | CABLE JUMPER 1MM .152M 21POS |
| GEC31DRAH | CONN EDGECARD 62POS R/A .100 SLD |
| ESC12DRYN | CONN EDGECARD 24POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AGLP030V2-CS201 | 功能描述:IC FPGA IGLOO PLUS 30K 201-CSP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO PLUS 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| AGLP030V2-CS201I | 功能描述:IC FPGA IGLOO PLUS 30K 201-CSP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO PLUS 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| AGLP030-V2CS289 | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology |
| AGLP030V2-CS289 | 功能描述:IC FPGA IGLOO PLUS 30K 289-CSP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOO PLUS 标准包装:152 系列:IGLOO PLUS LAB/CLB数:- 逻辑元件/单元数:792 RAM 位总计:- 输入/输出数:120 门数:30000 电源电压:1.14 V ~ 1.575 V 安装类型:表面贴装 工作温度:-40°C ~ 85°C 封装/外壳:289-TFBGA，CSBGA 供应商设备封装:289-CSP（14x14） |
| AGLP030-V2CS289ES | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOO PLUS Low-Power Flash FPGAs with FlashFreeze Technology |
发布紧急采购，3分钟左右您将得到回复。